
Excertos do catálogo

DVTR2800S SeriesHIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION The DVTR series of high-reliability DC-DC converters provide decades of successful critical mission support. Operable over the full military (-55 °C to +125 °C) temperature range with no power derating, the DVTR series unique input, and output filters dramatically reduce input and output noise performance. While operating at a nominal fixed frequency of 450 kHz, these regulated, isolated units utilize a high-speed magnetic feedback design and well-controlled under-voltage lockout circuitry to eliminate slow start-up problems. These converters are designed and manufactured in a facility qualified to ISO9001 and certified to MIL-PRF-38534 and MIL-STD-883. This product may incorporate one or more of the following U.S. patents: 5,784,266 5,790,389 5,963,438 5,999,433 6,005,780 6,084,792 6,118,673 FEATURES • High Reliability • Very Low Output Noise • Wide Input Voltage Range: 15 to 50 Volts per MIL-STD-704 • Up to 40 Watts Output Power • Fault Tolerant Magnetic Feedback Circuit • Output Voltage Trim Up +10% • NO Use of Optoisolators • Undervoltage Lockout • Indefinite Short Circuit Protection • Current Limit Protection • Industry Standard Pinout • High Input Transient Voltage: 80 Volts for 1 sec per MIL-STD-704A • Precision Seam Seal Hermetic Package • High Power Density: > 40 W/in3 • Custom Versions Available • Additional Environmental Screening Available • Meets MIL-STD-461 Revisions C, D, E and F EMC Requirements When Used With VPT’s EMI Filters • Flanged and Non-flanged Versions Available • MIL-PRF-38534 Element Evaluated Components • Space Applications should consider VPT’s "S” Series of Radiation Tolerant Power Conversion Devices. Contact VPT for details. Sales Information: Phone: (425) 353-3010 Fax: (425) 353-4030 E-mail: vptsales@vptpower.com
Abrir o catálogo na página 1
Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. Correction factor of 0.12 added to ceramic capacitors.
Abrir o catálogo na página 2
Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. Correction factor of 0.12 added to ceramic capacitors.
Abrir o catálogo na página 3
Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. Correction factor of 0.12 added to ceramic capacitors.
Abrir o catálogo na página 4
Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. Correction factor of 0.12 added to ceramic capacitors.
Abrir o catálogo na página 5
Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. Correction factor of 0.12 added to ceramic capacitors.
Abrir o catálogo na página 6
Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. Correction factor of 0.12 added to ceramic capacitors.
Abrir o catálogo na página 7
DVTR2800S Series BLOCK DIAGRAM PIN 1 UNDER VOLTAGE SHUTDOWN PRIMARY HOUSEKEEPING SUPPLY VOLTAGE AND CURRENT AMPLIFIERS SECONDARY HOUSEKEEPING SUPPLY CONNECTION DIAGRAM
Abrir o catálogo na página 8
DVTR2800S Series INHIBIT DRIVE CONNECTION DIAGRAMS OPTIONAL CAPACITOR OPTIONAL CAPACITOR Figure 4 – Internal Inhibit Circuit and Recommended Drive Figure 5 – Isolated Inhibit Drive (Shown with optional capacitor for turn-on delay) (Shown with optional capacitor for turn-on delay) EMI FILTER HOOKUP DIAGRAM Figure 6 – Converter with EMI Filter
Abrir o catálogo na página 9
The output voltage can be trimmed up by connecting a resistor between the +S pin (PIN 6) and the OUT COM pin (PIN 4). The maximum trim range is +10%. The appropriate resistor values versus the output voltage are given in the trim table below. The -S pin should be connected to the OUT COM pin. (Continued on next page)
Abrir o catálogo na página 10
Notes: 1. Connect R-TRIM = 400Q from +VOUT (PIN 5) to +S (PIN 6).
Abrir o catálogo na página 11
DVTR2800S Series EFFICIENCY PERFORMANCE CURVES (TCASE = 25°C, Full Load, Unless Otherwise Specified) VIN = 16V Efficiency (%) vs. Output Power (W) Efficiency (%) vs. Output Power (W) Efficiency (%) vs. Output Power (W) Efficiency (%) vs. Output Power (W)
Abrir o catálogo na página 12
DVTR2800S Series EFFICIENCY PERFORMANCE CURVES (TCASE = 25°C, Full Load, Unless Otherwise Specified) VIN = 16V Efficiency (%) vs. Output Power (W) Efficiency (%) vs. Output Power (W) Efficiency (%) vs. Output Power (W) Efficiency (%) vs. Output Power (W)
Abrir o catálogo na página 13
DVTR2800S Series EFFICIENCY PERFORMANCE CURVES (TCASE = 25°C, Full Load, Unless Otherwise Specified) VIN = 16V Efficiency (%) vs. Output Power (W) Efficiency (%) vs. Output Power (W)
Abrir o catálogo na página 14
DVTR2800S Series EMI PERFORMANCE CURVES (TCASE = 25°C, VIN = +28V ± 5%, Full Load, Unless Otherwise Specified) Figure 18 – DVTR2800S without EMI Filter Figure 19 – DVTR2800S with EMI Filter
Abrir o catálogo na página 15
Figure 20 - Non-Flanged, Seam Seal Package and Pinout
Abrir o catálogo na página 16
Figure 21 - Flanged, Seam Seal Package and Pinout
Abrir o catálogo na página 17
DVTR2800S SeriesENVIRONMENTAL SCREENING (100% Tested Per MIL-STD-883 as referenced to MIL-PRF-38534) Test 1. Contact Sales for more information concerning additional environmental screening and testing options desired. 2. VPT Inc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our sole discretion unless specifically forbidden by customer contract. 3. 100% R&R testing with all test data included in product shipment. 4. Not required per MIL-PRF-38534. Test is performed for additional product quality assurance. 5. Non-QML products may not meet all...
Abrir o catálogo na página 19Todos os catálogos e folhetos técnicos VPT INC.
-
DVETR2800S
16 Páginas
-
DVEHF2800T
12 Páginas
-
DVPL0510S
13 Páginas
-
DVPL0505S
13 Páginas
-
DVPL0503S
12 Páginas
-
DVMSA28
9 Páginas
-
DVFL2800D
28 Páginas
-
DVFL2800S
30 Páginas
-
DVHE2800S
15 Páginas
-
DVTR2800D
21 Páginas
-
DVTR2800T
15 Páginas
-
DVWR2800T
14 Páginas
-
DVHF2800D
17 Páginas
-
DVHF2800S
18 Páginas
-
DVAB2800D
14 Páginas
-
DVHF+2800T
17 Páginas
-
DVHV2800D
17 Páginas
-
DVSB2800D
14 Páginas
-
DVHV2800S
17 Páginas
-
DVGF+2800T
15 Páginas
-
DVSA2800D
16 Páginas
-
DVSA2800S
15 Páginas
-
DVCH2800S
14 Páginas