IPC_E2_R2
1 / 99Páginas

FACTORY ULTRAMAGIC, S.A. Aeròdrom Igualada – Òdena, s/n 08700 Igualada (BCN – Spain) Phone (+34)93.804.22.02 – Fax (+34) 93.803.56.04 Spares Order: gestio@ultramagic.com Technical Office: techinfo@ultramagic

INTRODUCTION This Ultramagic Balloons Parts Catalogue has been designed to enable an easy identification of the spare parts that you may need for your Ultramagic Balloon. Parts must be always fitted in accordance with the appropriate Maintenance Manual, which can be downloaded from the Ultramagic website (www.ultramagic.com). The authorisation to carry out work on your balloon is given in any case by the Local Civil Aviation Authority according to the regulation applicable. ...

SYMBOLS AND ACRONIMS Assembly Part may require adjustment before or at assembling Part replacement ‘on condition’ * Symbols above are used as guidance only. Handling and fitting of the parts must always be carried out in accordance to the latest approved Maintenance Manual, which always takes precedence to this IPC.

FDS LINES PULLEY (SEWN TO PARACHUTE)

ENVELOPE WIRES Special care should be taken when ordering envelope flying wires, as lengths vary depending on the position on the envelope. However there are 4 identical sets of wires on each envelope terminating at each corner of the load frame. The exception to this rule is where an 8 pole system is used with larger baskets/envelope combinations but there are still 4 sets of wires around the envelope. The wires can be a single wire or consist of a pair, again depending on the position on the envelope wire. ...

PARACHUTE EDGE TAPE BLACK (Dashed) KEVLAR ARAMIDE LOAD TAPE – Tekno Envelopes

DESCRIPTION 2.5mm KEVLAR‐POLYESTER PARACHUTE RIGGING CORD 3.0mm KEVLAR PARACHUTE RIGGING CORD 4.0mm BLUE KEVLAR CORE VENT LINE

SECTION 2. BURNERS A. MK‐21 BURNER DOUBLE BURNER ASSEMBLY CENTREGIMBAL MOUNTING

PILOT REGULATOR VALVE ASSEMBLY (FILTER NOT INCLUDED) PRESSURE GAUGE ASSEMBLY (INCLUDES BACK SEALS)

BURNER BLOCK Fuel hose

VALVE COVER VALVE BODY ASSY (COMMON) MAIN HANDLE LIQUID HANDLE

LIQUID VALVE HANDLE– ALTERNATIVE, FIXED OPEN (BLUE) NYLON THRUST WASHER – LIQUID VALVE (VARIOUS THICKNESSES) LIQUID VALVE HANDLE – STANDARD, DEAD MAN'S (BLUE)

REGULATOR FILTER (INCLUDES O‐RING)

PILOT LIGHT CAP (INCLUDES MESH AND GRUB SCREW)

VARIOUS POSNS FEMALE SPIN COUPLING RIGHT HAND TOMAC CYLINDER ASSEMBLY

ISOLATION VALV E SUB-A S SY

REMOTE CONTROL MODULES (ELECTRONICS ONLY)

CRUISE CONTROL VALVE ASSEMBLY – RIGHT HAND CRUISE CONTROL VALVE ASSEMBLY – LEFT HAND LEFT HAND RIGHT HAND VAPOUR BALL VALVE ¼”NPT RIGHT HAND* VAPOUR BALL VALVE ¼”NPT LEFT HAND*

CENTRE GIMBALTRIPLE ASSEMB LY ID

CENTRE GIMBAL QUAD ASSEMB LY ID

BOTTOM VIEW RIGHT PILOT REGULATOR VALVE ASSEMBLY – BLUE LEFT PILOT REGULATOR VALVE ASSEMBLY – RED

LEFT LIQUID VALVE HANDLE (DEAD MAN) – RED

IGNITER ELECTRODE (FOR BURNER WITH VAPOUR PILOT LIGHT) PRESSURE GAUGE (INCL. COPPER SEAL) LEFT SIDE BURNER CAN ‐ LIMITED AVAILIABILITY‐ LEFT SIDE BURNER CAN (VAPOUR PILOT) ‐ LIMITED AVAILIABILITY‐ RIGHT SIDE BURNER CAN ‐ LIMITED AVAILIABILITY‐

LIQUID PILOT VALVE, INCL. NUT & WASHER (COMMON TO LH AND RH)

MAIN VALVE HANDLE LH (SMOOTH) INCL. REGISTRATION SYSTEM MAIN VALVE HANDLE RH (SLOTTED) INCL. REGISTRATION SYSTEM

MALE UNION FITTING (INCL. CONCIAL SEALS AND NUT)

SECTION 2C. BMK‐008 POWERPLUS SPORT Due to the sharing of parts, Double burner version of the Powerplus Sport is used for P/N identification. Specific items applicable only to the single version are shown in separate assemblies at the end of this section.

PILOT LIGHT INLET FILTER HOUSING (INCL. FILTER)

BLAST & LIQUID JET VALVE SLEEVE O‐ RING

SINGLE BURNER MOUNTING TO BURNER FRAME ST STL DETTACHABLE RADIUS ARM ‐ BURNER SIDE ST STL DETTACHABLE RADIUS ARM ‐ FRAME SIDE

PILOT LIGHT INLET FILTER HOUSING (INCL. FILTER)

TRIPLE BAR HANDLE CONNECTION SHORT

RAW HIDE* (SENT SOAKED OR DRIED)

TOWING PLATES (PAIR) INCL. BOLTS & NUTS

EXTERNAL CYLINDER SUPPORT BRACKET LEFT

CROSS TENSOR – BUCKLE END (FOR BOTH SHORT AND LONG SIDES) INTERNAL CYLINDER CROSSED STRAPS WITH POCKET, VARIOUS COLORS*

SECTION 4. HOSES AND FITTINGS Special care should be taken when ordering fuel hoses, due to the variety of dimensions and couplings. It is strongly recommended to measure the existing hose as shown below and provide the right Part Number. LENGTH

CYLINDER INTERCONNECTION “T” HOSE – REGO

LIQUID TAKE OFF VALVE BARE (INCL. BLUE HANDLE)

FOR INTEGRATED TYPE REF. VAPOUR VALVE SECTION PRESSURE RELIEF VALVE – REGO, BRASS (VALVE ONLY, OLD STYLE)* PRESSURE RELIEF VALVE – TECVAL (COMPLETE, INCL. DEFLECTOR & CAP) PRESSURE RELIEF VALVE – TECVAL (VALVE ONLY) PRESSURE RELIEF VALVE DEFLECTOR FITTING FOR INTEGRATED TYPE ‐ ‐ ‐ ‐ REF. VAPOUR VALVE SECTION Valves are delivered with Date engraved for service life control

VAPOR REGULATOR STD (BULLFINCH) VAPOUR QUICK COUPLING LEGRIS ‐ STANDARD

READOUT ASSEMBLY SENSOR ASSEMBLY

Fits to: MK‐21 DOUBLE/TRIPLE/QUAD (Centre Gimbal Style), BMK‐008 DOUBLE, BMK‐050 DOUBLE/TRIPLE/QUAD ID PICTURE CAT. NR. P/N DESCRIPTION 1

LEFT ISOLATION VALVE HANDLE COLOR RED

HANDLE POST LONG ‐ HYDRAULIC VERSION

Engine Type Propeller Type [h ]9 13 FG W O O D 3 5.5 660mm Screwed 850mm Screwed, Reinforced 880mm Screwed, Reinforced

BONANNO QUICK RELEASE (ROPE NOT INCLUDED)

BONANNO REFUEL FILTER (HOSES NOT INCLUDED)

ENVELOPE FOLDING STRAP LONG (ENVELOPE