DVWR2800T
14Pages

DVWR2800T SeriesHIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION The DVWR series of high-reliability DC-DC converters provide decades of successful critical mission support. Operable over the full military (-55 °C to +125 °C) temperature range with no power derating, the DVWR series unique input, and output filters dramatically reduce input and output noise performance. While operating at a nominal fixed frequency of 450 kHz, these regulated, isolated units utilize a high-speed magnetic feedback design and well-controlled under-voltage lockout circuitry to eliminate slow start-up problems. These converters are designed and manufactured in a facility qualified to ISO9001 and certified to MIL-PRF-38534 and MIL-STD-883. This product may incorporate one or more of the following U.S. patents: 5,784,266 5,790,389 5,963,438 5,999,433 6,005,780 6,084,792 6,118,673 FEATURES • High Reliability • Very Low Output Noise • Wide Input Voltage Range: 15 to 50 Volts per MIL-STD-704 • Up to 25 Watts Output Power • Fault Tolerant Magnetic Feedback Circuit • NO Use of Optoisolators • Undervoltage Lockout • Indefinite Short Circuit Protection • Current Limit Protection • Industry Standard Pinout • High Input Transient Voltage: 80 Volts for 1 sec per MIL-STD-704A • Precision Seam Welded Hermetic Package • High Power Density: > 28 W/in3 • Custom Versions Available • Additional Environmental Screening Available • Meets MIL-STD-461C and MIL-STD-461D EMC Requirements When Used With a DVMC28 EMI Filter • Flanged and Non-flanged Versions Available. • MIL-PRF-38534 Element Evaluated Sales Information: Phone: (425) 353-3010 Fax: (425) 353-4030 E-mail: vptsales@vptpower.com

SPECIFICATIONS (Tcase = -55°C to +125°C, Vin = +28V ± 5%, Full Load5, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS

DVWR2800T SeriesSPECIFICATIONS (Tcase = -55°C to +125°C, Vin = +28V ± 5%, Full Load5, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS 1. This note intentionally not used. 2. Time for output voltage to settle within 1% of its nominal value. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 6. Up to 70% of the total auxiliary power or current can be drawn from either of the auxiliary outputs. 7. Synchronization is TTL signal with Vsync max = 6V. 8. -Vaux is 5% Load to Full Load at -55°C. 9. Correction...

DVWR2800T Series BLOCK DIAGRAM PRIMARY HOUSEKEEPING SUPPLY TRANSFORMER ISOLATED ERROR SIGNAL FEEDBACK VOLTAGE AND CURRENT ERROR AMPLIFIERS TRANSFORMER ISOLATED POWER FEEDFORWARD SECONDARY HOUSKEEPING SUPPLY

DVWR2800T Series CONNECTION DIAGRAM INHIBIT DRIVE CONNECTION DIAGRAMS BIAS OPTIONAL CAPACITOR IN COM 10 BIAS OPTIONAL CAPACITOR Figure 4 – Internal Inhibit Circuit and Recommended Drive Figure 5 – Isolated Inhibit Drive (Shown with optional capacitor for turn-on delay) (Shown with optional capacitor for turn-on delay)

DVWR2800T Series EMI FILTER HOOKUP DIAGRAM DVMC28 EMI FILTER 1 Figure 6 – Converter with EMI Filter

DVWR2800T Series EFFICIENCY PERFORMANCE CURVES (TCASE = 25°C) VIN = 15V Figure 7 – DVWR283R312T Efficiency (%) vs. Output Power (W) Figure 8 – DVWR283R315T Efficiency (%) vs. Output Power (W)

DVWR2800T Series EMI PERFORMANCE CURVES (TCASE = 25°C, VIN = +28V ± 5%, Full Load, Unless Otherwise Specified) Figure 9 – DVWR2800T without EMI Filter Figure 10 – DVWR2800T with EMI Filter

DVWR2800T SeriesPACKAGE SPECIFICATIONS (NON-FLANGED, SEAM SEAL) Pin Figure 11 - Non-Flanged, Seam Seal Package and Pinout

DVWR2800T SeriesPACKAGE SPECIFICATIONS (FLANGED, SEAM SEAL) Pin Figure 12 - Flanged, Seam Seal Package and Pinout

DVWR2800T SeriesENVIRONMENTAL SCREENING (100% Tested Per MIL-STD-883 as referenced to MIL-PRF-38534) Test 1. Contact Sales for more information concerning additional environmental screening and testing options desired. 2. VPT Inc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our sole discretion unless specifically forbidden by customer contract. 3. 100% R&R testing with all test data included in product shipment. 4. Not required per MIL-PRF-38534. Test is performed for additional product quality assurance. 5. Non-QML products may not meet all...

DVWR2800T SeriesORDERING INFORMATION DVWR Notes: 1. Contact the VPT Inc. Sales Department for availability of Class H (/H) and KL1 (/KL1) qualified products. 2. VPT Inc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our sole discretion unless specifically forbidden by customer contract. 3. -KL1 products are identical in every way with Class K products in compliance with MIL-PRF-38534 revision L and later revisions except they contain elements evaluated to the requirements of MIL-PRF-38534 revision K and previous revisions. These devices are not...

DVWR2800T SeriesSMD (STANDARD MICROCIRCUIT DRAWING) NUMBERS Standard Microcircuit Drawing (SMD) Do not use the DVWR2800T Series similar part number for SMD product acquisition. It is listed for reference only. For exact specifications for the SMD product, refer to the SMD drawing. SMDs can be downloaded from the DLA Land and Maritime (Previously known as DSCC) website at https://landandmaritimeapps.dla.mil/programs/defaultapps.asp. The SMD number listed above represents the Federal Stock Class, Device Type, Device Class Designator, Case Outline, Lead Finish and RHA Designator (where...