302
3Pages

302 STAINLESS STEEL, UNS S30200Strip, Coil, Foil & Wire, AMS 5515 & AMS 5516 (Annealed), AMS 5903 (1/4 Hard), AMS 5904 (1/2 Hard), AMS 5905 (3/4 Hard), AMS 5906 (Full Hard) Applications Springs, Fasteners, Washers, Clips, Clamps, Electrical Connectors, Contacts Description Type 302 is an austenitic stainless steel capable of attaining high strengths and ductility by cold working. Type 302 is not hardenable by heat treatment and in non-magnetic in the annealed condition. It becomes increasingly magnetic with cold working. If carbide precipitation is an issue 304 may be a better choice with its lower carbon content. Chemistry Typical Carbon: 0.08-0.15 Manganese: 2.00 max Silicon: 1.00 max Chromium: 17.00-19.00 Nickel: 7.00-10.00 Molybdenum: 0.75 max Phosphorus 0.040 max Sulphur: 0.030 max Iron: Balance Physical Properties Density: 0.29 lbs/in3 8.03 g/cm3 Electrical Resistivity: microhm-in (microhm-cm): At 68 °F (20 °C): 27.4 (69.5) At 1200 °F (659 °C): 45.8 (116) Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels & Special Metals, Inc., be liable for any damages arising from the use of the Information Included In this document or that It Is suitable for the 'applications' noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document. Copyright January 2014 Revision 03.01.2016. Ulbrich Stainless Steels & Special Metals, Inc. All rights reserved. We Deliver Precision®

Specific Heat: BTU/lb/°F (kJ/kg-K): 32-212 °F (0-100 °C): 0.12 (0.50) Thermal Conductivity: BTU/hr/ft2/ft/°F (W/nvK) At 212 °F (100 °C)-9.4 (16.2), At 932 °F (500 °C) - 12.4 (21.4) Mean Coefficient of Thermal Expansion: in/in/°F (pm/nvK) 32-212 °F (0-100 °C) - 9.4 x 10'6 (16.9) 32 - 600 °F (0-315 °C) - 9.9 x 10 6 (17.8) 32 - 1000 °F (0 - 538 °C) - 10.2 x 10 6 (18.4) 32 - 1200 °F (0 - 649 °C) - 10.4 x 10 6 (18.7) Modulus of Elasticity: ksi (MPa) 28.0 x 103 (193 x 103) in tension 11.2 x 103 (78 x 103) in torsion Magnetic Permeability: H = 200 Oersteds: Annealed < 1.02 max. Melting Range: 2250...

Finishes # 1 - Hot rolled annealed and descaled. It is available in strip, foil and ribbon. It is used for applications where a smooth decorative finish is not required. # 2D - Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process. # 2B - Smooth finish produced by cold rolling, annealing and descaling. A light cold rolling pass is added after anneal with polished rolls giving it a brighter finish than 2D. #BA- Bright annealed cold rolled and bright annealed #CBA- Course bright annealed...