Test certificate Z-41.3-325 Resistance class K90/K60 NW 100/125/160 and 200 Mounting frame for the installation into: ED brickwork or concrete floor EW-L light partition walls, metal support walls EW-L-40 light partition walls, wall thickness 40 mm Test certificate Z-41.3-333 Resistance class K30/0 Essential advantages • • Accessories (optional): MS-E electrical limit switch RT inspection tee SNP-S male sleeve connection NP male-male connector VMT disk valve for overflow opening The BEK-K90 is suitable for the installation into light F90 and F30 partition walls. The damper is mounted directly into the fire protected zone. The effectiveness of the fire protection is guaranteed by the butterfly blades. The dampers may even be mounted subsequently into ventilation systems in order to meet the effective fire prevention requirements. No special fixing arrangements are required (i.e. saving of time and high economy). Essential features 1/ Safety classification. • Official classification: Resistance class K90 and K30 • Release from 72 °C upwards • Maximum sealing between the body and the blades • Flame stability 2/ Low noise level • Insignificant reduction of cross-sectional area • High airflow rate • Any direction of airflow 3/ Sizes available • NW 100/125/160 and 200 Safety The Strulik BEK-K90 and K30 dampers have been submitted to many test series in Germany and abroad. These test series did not only include the effectiveness of FIRE PROTECTION and FLAME TIGHTNESS, but also the STABILITY OF FLAMES and the correct functioning of the FUSIBLE LINK. In Germany the damper has been tested against fire and smoke in accordance with the principles of construction and testing of the "Deutsches Institut für Bautechnik" in Berlin. The expert opinion for a K90 and K30 resistance class has been prepared by the "Institut für Haustechnik" of the Technical University of Munich. VdS in Cologne has prepared the test report on the release mechanism for an activation temperature of 72 °C in accor

* Installation into brickwork walls, wall thickness min. 115 mm Installation into gas concrete walls, wall thickness min. 100 mm Installation into DIN 18163 wall panels, min. 80 mm Installation into concrete walls and floors, floor thickness min. 100 mm Test certificate Z-41.3-325 Resistance class K90/K60 Test certificate Z-41.3-333 Resistance class K30/0 Installation into a brickwork or concrete floor For the installation into brickwork or concrete floors always together with the ED mounting frame The correct installation of the BEK-K90 and K30 damper is performed together with a wall frame...

Installation into walls of brickwork, concrete or gas concrete Opening max. 2 mm larger than the mounting frame Test certificate Z-41.3-325 Resistance class K90/K60 Installation into solid walls Operating side Concrete wall thickness min. 100 mm Brickwork min. 100 mm Installation into solid walls and floors Operating side Minimum distances of the dampers for the installation into solid walls and floors Operating side Insert spindle, coat and smooth with gap filler or glue with the SBK 2000 adhesive (dry construction). When connecting ventilation ducts, the connection has to be flexible. Alternatively,...

Installation into light F90 partition walls BEK-K90-EW-L Test certificate Z-41.3-325 Resistance class K90/K60 Per wall side three angles (A) staggered by 120°; angles (B) shall not be fastened on the opposite side, but staggered by 60° Insert sleeve and coat and smooth with gap filler Installation into light partition walls Fastening inside the light partition walls Six angles, angle A (three) staggered by 120° fastened if the wall thickness has been stated, angle B (three) delivered loosely. Dimensions Test certificate Z-41.3-333 Resistance class K30/0 Inspection side ALUFLEX duct on both sides...

Fastening inside the light partition walls Test certificate Z-41.3-325 Resistance class K90/K60 Six angles, angle A (three) staggered by 120° fastened if the wall thickness has been stated, angle B (three) delivered loosely. Dimensions Test certificate Z-41.3-333 Resistance class K30/0 Permissible ducts The dampers shall only be connected to ventilation ducts, which due to their design or laying, will not apply considerable forces to the dampers as a result of warming. Ventilation ducts may be connected to dampers with a compensator or spigot of flexible aluminum ductwork that is at least 10...

Inspection T iron Type: RT Connecting collar Test certificate Z-41.3-325 Resistance class K90/K60 Inspection cover Test certificate Z-41.3-333 Resistance class K30/0 Facilities for inspection Type: RT Suitable for all purposes, i.e. inspection above and beneath the floor within brickwork or gas concrete walls. Inspection cover and connecting collar exchangeable. Concrete floor, brickwork or gas concrete wall Type: SNP-S The male sleeve connection is inserted into the spirally wound duct like a telescope, so that the opening is free for inspection. Type: NP The male-male connector together with...

Test certificate Z-41.3-325 Resistance class K90/K60 Test certificate Z-41.3-333 Resistance class K30/0 Design diagrams Pressure drop and noise level The BEK-K90 and BEK-K30 can be used independently from the direction of airflow. The air velocity of ≤ 8 m/s shall not be exceeded for ventilation reasons. Airflow rate

ED mounting frame for walls and floors Test certificate Z-41.3-325 Resistance class K90/K60 Test certificate Z-41.3-333 Resistance class K30/0 Wall clamp Technical data of the mounting frame Mounting frame for walls and floors Type: ED Scope of delivery: Mounting frame and two wall clamps Mounting frame for light partition walls Type: EW-L Scope of delivery: Mounting frame, six angles and six spring folding dowels Type: EW-L40 Scope of delivery: Mounting frame, six angles and six wooden screws 4 x 60 mm Inspection side Fastening inside light partitions EW-L and EW-L40 mounting frame for light...