Catalog excerpts
AXLE JACK - 45T (T-type with air pump) Operating instruction Shanghai Junxun Aviation Technology
Open the catalog to page 1
AXLE JACK - 45T (T-type with air pump) Operating instruction Foreword Our company is a designated manufacturer of aircraft ground equipment for major airlines in the country, and has more than 20 engineers and researchers who have been engaged in the development of ground equipment for more than 20 years. The company has recently launched a new type of aircraft axle jack, which changed the phenomenon of internal leakage caused by the previously used reversing valve, which could not keep the pressure, and the operation was simpler, reaching or even exceeding the level of similar products...
Open the catalog to page 2
AXLE JACK - 45T (T-type with air pump) Operating instruction Ⅲ.Technical parameters Axle jacks technical parameters Parameter table of double-acting axle jacks Type JXHK-GB-1345 A:The min.height B:Hydraulic Lift C:Extension screw D:The max.height E:Base width F:The length of tank Ⅳ. Product structure The axle jacks are mainly composed of base, bracket, fuel tank, oil cylinder,sleeve oil cylinder, piston,adjusting screw, low pressure pump, high pressure pump,fuel tank, oil cylinder, sleeve oil cylinder, piston
Open the catalog to page 3
AXLE JACK - 45T (T-type with air pump) Operating instruction 1. Adjusting screw 2. Piston 3. Sleeve cylinder 4. Oil cylinder 5. Base 6. Fixing screw 7. Directional wheel 8. Directional wheel support spring plate 9. Fixing screw 10. Nut 11. Spring washer 12. Universal wheel 13 .Valve pump seat 14. Pressure gauge 15. Lifting hand 16. Connecting rod 17. Pipe joint 18. Connecting screw 19. Oil pipe 20. Large pump 21. Small pump 22. Fuel tank cover 23. Oil cup 24. Operating rod 25. Fuel tank 26. Handwheel 27. Pull rod 28. Operating rod support sleeve I 29. Operating rod support sleeve II 30....
Open the catalog to page 4
AXLE JACK - 45T (T-type with air pump) Operating instruction Hydraulic schematic diagram Figure 2 Tighten the handle clockwise, at this time the operation of large and small pumps or the use of air source through the pneumatic pump pressure oil through the valve body into the bottom of the cylinder, the cylinder quickly lift, and the top of the heavy, and the cylinder wall of the oil through the relief valve with relief valve constant pressure relief valve by pressure forced to open the relief valve, so that the oil back to the tank. Tighten the handle counterclockwise direction, and the...
Open the catalog to page 5
AXLE JACK - 45T (T-type with air pump) Operating instruction Ⅴ.check before operation Every time the jack is used, it must be checked carefully 1. Check whether the hydraulic oil in the tank is sufficient, and the liquid level must reach the tank 4/5 of the height. If insufficient, please add 10# or 15# aviation hydraulic oil. 2. Check whether the surface of the hydraulic cylinder is damaged, and the hydraulic pipeline and pipe joint are whether there is seepage, oil leakage. 3, check whether the manual pump and pneumatic pump work normally. When all is well can operate. Ⅵ. Operation 1....
Open the catalog to page 6
AXLE JACK - 45T (T-type with air pump) Operating instruction Ⅶ, jack disassembly 1. Fix the base and rotate it counterclockwise with a hexagonal wrench to remove the oil cylinder from the base. Otherwise, the oil cylinder can be reloaded. (3) Tighten the lid of the oil tank. Figure 3 1. O-ring 2. Retaining ring 3. O-ring 4. Retaining ring 5. O-ring 6. Retaining ring 7. O-ring 8. Retaining ring 9. O-ring 10. Retaining ring 11. O-ring 12. Retaining ring 13. Limiting cylindrical pin 14. Steel wire retaining ring 2. Adjust the screw With the jack head facing down, the adjusting screw can be...
Open the catalog to page 7
Operating instruction AXLE JACK - 45T (T-type with air pump) 3. Hydraulic pump body and pump core (1) Put the jack on the side and turn it counterclockwise with a wrench to remove the pump body from the valve seat; (see Figure 4) Figure 4 1.Pin shaft 2. Dust ring Ⅰ 3. High pressure pump 4. Pump core Ⅰ 5.O retaining ring 6. O-ring 7. Y-ring I 8. O-ring 9. Copper rectangle 10. Steel ball I 11. Connecting rod 12. Cotter pin 13. Connecting rod 14. Dust ring Ⅱ 15. Low pressure pump 16. Pump core Ⅱ 17. Retaining ring 18. O-ring 19. Y-shaped sealing ring Ⅱ 20. Copper rectangular ring 21. Steel...
Open the catalog to page 8
AXLE JACK - 45T (T-type with air pump) Operating instruction Ⅷ. Troubleshooting and troubleshooting Common faults of jacks, causes of faults and troubleshooting methods (see table) Malfunction Oil leakage at the threaded connection between the pump body and the pump seat The hydraulic pump leaks oil from the dust ring Pipe joint leaking oil Oil leakage at the connection between the joint, the base and the pump base Oil leaking from handle Manual hydraulic pump can not absorb oil 1. Tighten the pump body 1. The pump body is not 2. Replace the copper tightened rectangular ring 2. The copper...
Open the catalog to page 9
AXLE JACK - 45T (T-type with air pump) Operating instruction Ⅸ, matters needing attention 1. Do not use the jack at super high or overload, so as not to damage the jack and cause danger 2. Do not load sideways or eccentrically during use 3. Strong vibration and bumping should be avoided during transportation to prevent damage to the jack oil pipe and pipe joints 4. The fastest pushing and pulling speed of the jack is 10km/h, and the jack shall not be pulled by a car 5. When the jack is not in use, the piston and pump core should be pressed down, and the rain cover should be covered to keep...
Open the catalog to page 10All Shanghai Junxun Aviation Technology Co. catalogs and technical brochures
-
Kitchen integrated test device37 Pages
-
SSJ100 fuselage jack11 Pages
-
B737 fuselage jack2 Pages
-
TB-09-JXS1 Pages
-
IAE1N200091 Pages
-
98A100010050001 Pages
-
Aircraft Maintenance Dock35 Pages
