- Products
- Catalogs
- News & Trends
- Exhibitions
BA 2
BA 2
- Working area per spindle: 200 x 350 x 300 mm
- Spindle distance: 200 mm
- Installation surface: 4 m²
- Maximum spindle speed: 36,000 rpm
- Rapid traverse speed: up to 70 m/min
- Chip-to-chip time: 2.00 seconds
- Maximum acceleration: 20 m/s²
- Positioning accuracy: deviation less than 0.006 mm
- Patented SW monoblock machine bed for stability and accuracy
- Box-in-open-box design for high system rigidity
- Direct absolute travel measuring system in all axes
- Swiveling workpiece carrier system with face gear as Q axis
- Energy-efficient hydraulic weight compensation system
- Tool magazine with 2 x 20, 2 x 40, or 2 x 60 slots
- High-speed machining with a Kv factor of 5 and a jerk of 500 m/s³
- Gantry drive in the Y axis for optimal positioning accuracy
- Hydraulic compensation reduces thermal load and boosts energy efficiency
- Tool magazine protected against chips and spray water
- Process optimization and simulation
- Tool testing and process development
- Unit cost calculations and maintenance contracts
- Training at the SW Academy
- Remote services and data analysis
- Drive system: Ballscrew
- Feed drive acceleration: X/Y/Z - 15/15/20 m/s²
- Max feed thrust: X/Y/Z - 4,500/6,500/4,500 N
- Toolchange system: Pick-Up
- Operating voltage: 3 x 400 Volt, 50 Hz
- Total connected load: 37 kVA
Catalog excerpts
SPINDLE DISTANCE 200 MM RAPID TRAVERSE UP TO 70 M/MIN O-CHIP TIME 2.00 S INSTALLATION SURFACE 4 M² ENERGY MANAGEMENT SYSTEM
Open the catalog to page 3
Machining small workpieces with two spindles The two-spindle BA 222 machining center with working area dimensions of 200 x 350 x 300 mm per spindle is setting new standards for 4 and 5-axis machining. On just 4 square meters of installation surface you can produce small steel, cast iron and light metal workpieces at extremely high speeds. With a conventional ball screw drive, the BA 222 is the counterpart of the BA W02-22 linear motor machine. It is also ideally suited for a highly diverse range of applications in precision engineering, such as watchmaking, the automotive industry and medical...
Open the catalog to page 4
Chip-to-chip in just 2.00 seconds With a spindle distance of 200 mm, the feed axes accelerate at up to 20 m/s2 to a rapid traverse of up to 70 m/min. In the first configuration level, the HSK-A40 motor spindles reach the maximum speed of 25,000 rpm within 0.7 seconds. The chip-to-chip time for a tool change is only 2.00 seconds. The double swiveling workpiece carrier allows you to load the BA 222 in parallel to production time, thereby further reducing auxiliary times. Increased energy efficiency In the Y axis an electronically coupled gantry drive ensures optimum positioning accuracy, even with...
Open the catalog to page 5
DIMENSIONS TECHNICAL DATA HSK-A40 WORKSPACE PER SPINDLE I 3350 | Working range X-axis Y-axis (toolchange position) Z-axis (Z1/Z2) Spindle distance Workpiece carrier Swivel carrier / counter bearing with crown gear: swivel time 0/180° A- and U-axis, prepared for mounting a fixture plate, up to max. Drive system Load capacity Speed range A-, U-axis C- and W-axis* Work spindle HSK-A40 Speed range Run up time 0 - nmax Spindle bearings 0 Power / Torque (40% duty cycle) Work spindle HSK-E40* Speed range Run up time 0 - nmax Spindle bearings 0 Power / Torque (40% duty cycle) Feed drive Drive system Rapid...
Open the catalog to page 7
There are quite many who build machining centres. But only a few take such intensive and successful care of the entire technological demand of your project like we do. The highest priority is given to deliver the best economical and sustainable solution for your manufacturing task. Which machine model ends up being the right one and how it will be applied most effectively, depends on your requirements for materials to be machined, quality and production volumes. Schwäbische Werkzeugmaschinen GmbH Seedorfer Straße 91 78713 Waldmössingen Germany We proclaim to be ’Technology People’. This is more...
Open the catalog to page 8
