- Catalogs
- Rosen Aviation
- 32" HD Bulkhead Display
32" HD Bulkhead Display
32" HD Bulkhead Display
- Dimensions are provided in inches unless otherwise specified, with tolerances defined as per ASME Y14.5M - 1994.
- Assembly weight is 18.8 lbs ±10%.
- Screen resolution is 1920 x 1080 pixels with a viewing area of 698.4 x 392.85 mm.
- Horizontal and vertical viewing angles are ±89º.
- Contrast ratio is 1300:1, and screen brightness is 450 cd/m².
- Power consumption is 93 W max, with power input requirements per DO-160E Cat Z(A).
- Minimum of six 4-40 fasteners required for mounting, with optional 8-32 mounting holes for back mounting.
- Clearance requirements include 1/2" clearance to top and bottom vent holes or back of unit, and a minimum clearance across the back of 3/16".
- Operating temperature range is 0ºC to 50ºC.
- Altitude tolerance up to 15,000 ft.
- Humidity tolerance up to 95% RH.
- Vibration tolerance is 1.48 grms.
- Radio frequency and emission of RF energy specifications are per DO-160F Cat T and Cat M respectively.
- Connector P3 is a 15-position male Tyco 205206-3, with specific pin assignments for power and signal connections.
- Connector P4 is a female RJ-45, with pin assignments for CAT6 signals and ground.
- ESD safe handling practices must be observed.
- Connector kits and interconnect cable recommendations are not included and should be referred to in Rosen document 105821.
Catalog excerpts
NOTES: (UNLESS OTHERWISE SPECIFIED) ELECTRONIC REVISION CONTROLLED 1. ASSEMBLY WEIGHT: 18.8 LBS. ±10% 2. HARNESS LENGTH: AS SHOWN 3. OBSERVE ESD SAFE HANDLING PRACTICES 4. SOME MINOR PARTS, LABELS, HARNESSES AND INSTRUCTION OMITTED FOR CLARITY 5. CLEARANCE REQUIREMENTS: 1/2" CLEARANCE TO TOP AND BOTTOM VENT HOLES OR 1/2" CLEARANCE TO BACK OF UNIT. MINIMUM CLEARANCE ACROSS BACK OF UNIT 3/16" 6. MINIMUM OF 6 EA 4-40 FASTENERS REQUIRED FOR MOUNTING REVISIONS DESCRIPTION ADD INTERCONNECT CABLE REF, DEL SHEET 3 OPTIONAL 8-32 MOUNTING HOLES FOR BACK MOUNTING MINIMUM 12 EA 8-32 FASTENERS REQD FOR OPTIONAL BACK MOUNTING MAXIMUM 1/4" PROJECTION OF FASTENER INTO CHASSIS FROM BACK SIDE 8. CONNECTOR KITS NOT INCLUDED DENOTES ROSEN AVIATION FAI INSPECTION DIMENSION 9. .129 THRU ALL .225 X 100° MOUNTING HOLES (4-40 SCREW) 1.5 MINIMUM BEND RADIUS THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO ROSEN AVIATION, LLC. IT SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART OR USED FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM ROSEN AVIATION, LLC. THIS DRAWING MAY BE COVERED UNDER ONE OR MORE U.S. OR INTERNATIONAL PATENTS, PLEASE CONTACT ROSEN AVIATION FOR SPECIFIC INFORMATION. OUTLINE AND INSTALLATION DRAWING, RDM 32" W/S, FEMALE RJ45 1020 OWEN LOOP SOUTH EUGENE, OREGON 97402 TEL: (541) 342-3802 FAX: (541) 342-4912 TITLE UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES .X = .1 .XX = .03 .XXX = .015 = RADII
Open the catalog to page 1
2 Connector Plug (P3) Pinout - 15 Position Mate: 15 Pin Female Tyco 205205-2 Contact: 66504-3 Connector Kit 0300-053 Environmental Specifications Operating Temperature Altitude Humidity Vibration Pow er Input Radio Frequency Emission of RF Energy Monitor signal Power Requirements** Monitor signal Connector: 15 Pin Male, Tyco 205206-3 LCD Performance* Screen Resolution (pixels) Display View ing Area (mm) Horizontal View ing Angle Vertical View ing Angle Contrast Ratio (Typical) Screen Brightness (Typical) FOR INTERCONNECT CABLE RECOMMENDATIONS SEE ROSEN DOCUMENT: 105821 ** SEE 0700-104-CD DRAWING...
Open the catalog to page 2All Rosen Aviation catalogs and technical brochures
technical manual32 Pages
catalog 201120 Pages
42" HD Bulkhead Display2 Pages
26" HD Bulkhead Display2 Pages
9" WS3 Pages