Product Data [email protected] T | +44 (0) 20 7631 1335

Flite Product Data Drawing on decades of OMK’s expertise in public seating, the Flite system is engineered with a compact footprint that maximises seating capacity in public spaces. A single, efficient bracket supports uniform seat and back panels, delivering a cost-effective yet high-performance beam seating solution for airports, transport hubs and busy waiting areas. Guaranteed against structural failure for a minimum of 25 years. Has been independently tested by FIRA to withstand 25 years of heavy contract use in accordance with BS EN 15373. Metal components are finished for interior use...

Flite Product Data Key Design Features • All components can be coloured to any RAL colour. • Flite incorporates 30 years of experience in the public seating sector, designed to maximise space.The small footprint offers 10% more seating over other systems. • A minimalist structure utilises a single bracket supporting 2 independent identical seat and back panels, allowing either to be easily replaced in situ in the event of damage without the necessity to replace or repair the whole seat. • A gap between the seat and back eliminates dirt accumulation and allows any spilt liquids to drain immediately....

Flite Product Data Flite Product Data Cast aluminium foot is made from aluminium-silicon alloy LM06. Finished in alochrom and powder coated. Available as standard or floor fixed. Seat and Back Panels Seat and back panels are available in the following finishes: Moulded Polyurethane • Self-skinned moulded polyurethane panels with a fabricated steel core. • Fabricated from 3mm steel sheet and tube. • Integral polyurethane. • Pressure injected around steel frames. • Incorporates threaded inserts to enable fixing. • Available in any RAL colour, dyed throughout. • Flame retardant to BS 5852: 1990...

Flite Product Data • Dyed throughout. Seat and Back Brackets Flite utilises a single bracket which is fixed to the extruded beam using mechanical fasteners. • Pressure die-cast aluminium alloy, LM06. • Finished in alochrom/alodine 1200 (corrosion preventive pre-treatment). • Polyester powder coated to 100 microns, available in any RAL colour. • Colour fastness conforms to DIN 54004. Armrests Armrests are made from pressure die-cast aluminium and can be added or subtracted on the units before or after assembly. • Pressure die-cast aluminium alloy, LM06. • Available in powder coat or polished aluminium...

Flite Power Arm Data Components 1. Power Socket Module (available in all international standards) • Nema 5-15R 110V AC receptacle • USB Charging Outlets: 2 x Type A Female • Charging Current: Max 2.3A total • AC Input Current: Max 0.2amp at full load • Rated Total Output: Less than 0.5mA at no load • Mean Time Before Failure: Min 5,000 hours at 25°and full load • Over Current Protection: Min 5,000 hours at 25°and full load • Short Circuit Protection: Yes - Auto Reset Power arm supplied as a sealed unit. USB canister can be reomved and replced in situ without electrical disconection. In event...

Flite Power Arm Data Wiring Loom 1. Power Arm connection 1 2. Cable extension modules 3. Connection to circuit (plug or hard wired) For product support please call +44 (0) 20 7631 1335 www.omkdesign.com Power Arm can be fitted or moved to any arm position

Flite Power Arm Data Cable Routing 1. Cable is concealed inside the beam and exits on underside to connect to floor box. 2. Wieland box link: Modular cable can be broken at these points for removal and replacement 4. Connection cable continues inside beam to next power unit if required Fitting 1. Connect cable to the loom. 2. Seat the power amr on to the beam ensuring cable is tucked inside. 3. First hand tighten, the mechanically tighten the M8 X 25mm CSK machine s.crew Replacement To replace or move a unit, simply reverse the process to remove and then refit the new unit in For product support...

Flite Dimensions The circular support beam allows up to seven seats as standard. Modular arms can be added at any position. Tables can be positioned on the end of the beam or in between individual seats. 2750 2750 *for reference only, sizes may vary on final product For product support please call +44 (0) 20 7631 1335

Specialists in public seating with over 60 years of experience. Our head office is located in central London where we manage global sales, design & production. OMK Design Ltd. 30 Gresse Street London W1T 1QR E | [email protected] T | +44 (0)207 631 1335 omkdesign.com