LED ELEVATED APPROACH, THRESHOLD, THRESHOLD WING BAR AND RUNWAY END LIGHT COMPLIANCES ICAO: Annex 14 - Volume I Fig. A2-1, A2-2, A2-3, A2-4, A2-8 FAA: L-862S AC150/5345-46 IEC: TS 61827 NATO: STANAG 3316 CAA: CAP 168 IAAE: TP312 APPLICATIONS Approach, Threshold, Threshold Wing Bar and Runway End for ICAO CAT I,II and III and military runways Used for Stop Bar lighting on ICAO/FAA taxiways BENEFITS • 60000 hours LED rated life at full intensity, but over 100000 hours in field operating conditions • In new installation, LED lights mean lower loads, lower size of CCRs and transformers, thus low life cycle costs • The light output is variable like a traditional halogen lamp, as indicated by the FAA "Engineering Briefing No.67" • Colour emitted directly by LEDs: absence of coloured filters ensures no energy losses and no colour shifts • Fully compatible with existing AFL infrastracture* • Designed with simplicity allowing longer maintenance intervals and fewer spare parts • Transparent front protection mechanically fastened to the body by means of a suitable frame with silicone gasket, making its replacement quick and easy • No optical adjustment after LED module or lens array replacement • Operating with any topology of CCRs designed in compliance with IEC or FAA requirements * For monitored fixtures, isolation transformer max size: 150VA PERFORMANCES • The electronic is strong-built and highly resistant to shock and vibration • Automatic adaptation to the frequency of the supply current • A surge protection device is provided in the electronics as required by the FAA "Engineering Briefing No.67" • Immediate detection of an internal fault • Lightweight and sturdy due to aluminium die-castings • Powder coating surface finishing to provide good corrosion resistance • Body balanced on a special support for proper and accurate horizontal and vertical aiming • High jet blast resistance due to the small size of the Threshold and Runway End fixture, 310 mm high • Protection degree: IP67 • Temperature range: -55°C to +55°C INSTALLATION • The fixture can be installed on pipe elbow or baseplate • Specific tools available for easy and precise installation (EnergyTechnology Via della Solidarieta, 2/1 40056 Valsamoggia Loc. Crespellano - Bologna (Italy) Tel: +39 051 66 56 611 - Fax:

www.ocem.com [email protected] TABLES POWER CONSUMPTION * (w/o Arctic Kit) Electrical System 1 Plug Approach White 38VA Approach Red 26VA Threshold/Threshold Wing Bar Green 30VA Runway End/FAA Stop Bar 20VA ICAO Stop Bar 17VA * Measured at 6.6 A  POWER FACTOR Input Step Power Factor

LERA - AC - P-001 - 0 - 0 Basic P/N: -Use Code: -(Refer to TABLE A) Configuration: P-001 = Fixture complete with breakable coupling C-050 = Fixture with special support and cable lead (L= 0.5 m)(*) C-250 = Semi-assembled fixture (AC and AR only)(*) (**) C-000 = Fixture without cable lead (*) Monitoring: 0 = Without Monitoring M = With Monitoring 0 = Without Arctic Kit (*) Supporting pole and breakable coupling must be ordered separately (**) This configuration is provided with special support and cable lead (L = 2.5 m) not assembled

REN EWAL PARTS FOR LIGHT UNIT 1 Cover with electronic 2 Cover gasket 3 LED module support 4 LED module support gasket 5 LED module 6 Lens array for LED module 7 Body 8 Transparent front protection gasket 9 Transparent front protection 10 Transparent front protection holder plate (painted in the colour of the emitted light) 11 Vertical aiming adjusting device 12 Special support 13 FAA L-823 plug 14 Breakable coupling Refer to the relevant technical manual for the complete list ACCESSORIES 013.0010 Set of two ryton rings for receptacle support inside pipe elbow 013.0008 Galvanized steel pipe elbow...