
Catalog excerpts

LOW PRESSURE FLEXIBLE HOSES ALUMINUM LINES BULKHEAD FITTING CUSTOM PRODUCTS HIGH PRESSURE LINES MASK ASSEMBLIES MASK PRESENTATION UNITS NEBULIZER KITS ON/OFF OXYGEN VALVES OVERBOARD DISCHARGE INDICATORS OXYGEN CONTROL PANELS OXYGEN COUPLINGS OXYGEN OUTLETS
Open the catalog to page 2
Aluminum Lines The 02 Corporation Aluminum Oxygen Lines are manufactured to meet specific oxygen plumbing requirements. These lines are used to transfer oxygen from an oxygen cylinder to remote oxygen delivery devices. Because each aircraft's layout is different, these lines must be tailored to fit each design, and this is commonly accomplished through customer-supplied specifications. With these specifications, the aluminum lines may include bends to help fit to the aircraft layout as well as to avoid other interior components. The most common fittings at the end of these lines are a...
Open the catalog to page 3
and the addition of lock wire to these connections is also available. Each Line Tap offers the addition of a Low Pressure Flex Hose, which is commonly used to connect to a remote oxygen delivery device. Other possibilities include the addition of unions, elbows, plugs, bleed valves, or whatever your system requires.
Open the catalog to page 4
Bulkhead Fittings The 02 Corporation Bulkhead Fittings are made from solid brass to offer both oxygen compatibility and corrosion resistance. The operating pressure range for these fittings is 0 - 2,000 psi, and the proof pressure is 3,000 psi. Our Oxygen Fill Valve is used for charging a high-pressure aircraft oxygen cylinder with a ground service station. Each Fill Valve includes a cap and chain assembly (chain length is 6 - 6 ’/z") to provide protection from contamination when not in use. Each valve also includes an internal filter to prevent any particulates from being transferred into...
Open the catalog to page 5
Our Straight Bulkhead Fitting provides end connections per AND10089, Style G, Size 3. The thread length on one end is shortened as shown in the illustration below: THREAD LENGTH SHORTENED
Open the catalog to page 6
Our Oxygen Fill Valve provides end connections per AND10089, Style G, Size 3, as shown in the illustration below:
Open the catalog to page 7
Our Elbow Adapter provides an end connection per AND10089, Style G, Size 3, and the other with an 1/8 NPT internal thread, as shown in the illustration below:
Open the catalog to page 9
If you have a special need for a product that requires custom and unique design specifications we will do our best to meet your requirements using the “Can Do” principle. We might not have the capability to manufacture every product needed, but we certainly welcome any opportunity or challenge. Because we specialize in Aircraft Oxygen Equipment, we are eager to manufacture any related products or components. We have previously met customer requirements for custom parts or assemblies, and below is a list of some examples: • Remote Fill Valves • Customized Fill Stations including pressure...
Open the catalog to page 10
Our Mask Dust Covers offer protection for your oxygen masks from dust and other particulates that might be harmful to breathe when the mask is used.
Open the catalog to page 12
Our Remote Fill Valves can be manufactured specifically to your design and dimensions to meet all of your compatibility requirements. The material used for the valve shown below is T-19-V Brass per CDA 332.
Open the catalog to page 13
The 02 Corporation High Pressure Lines are used with connections involving oxygen at high-pressure conditions. Each line is cleaned for oxygen service, has a maximum operating pressure of 2,400 psi, and is proof pressure tested to 3,000 psi. We use Copper tubing per ASTM-B-280 and silver braze each fitting to conform to QQ-B-654 or BAg-7. It is recommended that a “coil" remain in the line to allow for excessive pulling and/or vibration. We offer 1/16-inch O.D. capillary lines for high-pressure flows requiring a minimized internal flow area. These lines have intended uses such as connecting...
Open the catalog to page 14
All of our High Pressure Lines have an "-XX" or "-XXX” included in the part number that designates the length of the line, specified in inches. The length is measured from the end of one fitting to the other as shown in the illustration below. Example part number for ordering: O2C11T08 - 025 BASIC PART NUMBER LENGTH IN INCHES (25 inches shown here)
Open the catalog to page 15
1/16" CONE CAPILLARY DISCONNECT
Open the catalog to page 17
HEAT SHRINK 1/16" CONE CAPILLARY DISCONNECT
Open the catalog to page 18
1/16” CONE BOTH ENDS HEAT SHRINK
Open the catalog to page 19
3/16" CONE CAPILLARY DISCONNECT
Open the catalog to page 25
Line Tap Assemblies The 02 Corporation Line Tap Assemblies offer connections at any location along main oxygen feed lines. By simply adding a mounting hole in the oxygen line, our Line Taps are easily installed to provide additional oxygen line locations. The diameter of the mounting hole must be 0.109 inches in order to properly connect the Line Tap, and a silicone gasket provides a leak proof seal. Each Line Tap is machined with external holes to offer locations for lock wire. Our Line Tap Assemblies, Part Numbers 02C10T05 and O2C10T1 are made from 2014 aluminum and anodized green to...
Open the catalog to page 35
Basic Part Number Example part number for ordering: BASIC PART NUMBER FITTING SIZE CSEE TABLE) TUBE SIZE CSEE TABLE)
Open the catalog to page 36
Basic Part Number Example part number for ordering: BASIC PART NUMBER FITTING SIZE CSEE TABLE) TUBE SIZE CSEE TABLE)
Open the catalog to page 37
In the picture shown below is our Elbow Line Tap, part number 02C10T05-5-5, installed on an aluminum oxygen line. Lock wire was used after installation to prevent accidental removal of the line tap. This particular line tap is mated with a low-pressure flexible oxygen hose to deliver oxygen to an oxygen delivery device, such as a Mask Presentation Unit. We also offer Saddle Line Tap Assemblies, Part Numbers O2C10T3 and O2C10T4, for larger size tubing. The body is made from aluminum, and the clamp, pin, screw, and washer are all made from corrosion resistant steel The fitting end is...
Open the catalog to page 38
Basic Part Number Example part number for ordering: BASIC PART NUMBER FITTING SIZE CSEE TABLE) TUBE SIZE CSEE TABLE)
Open the catalog to page 39
Basic Part Number Example part number for ordering: BASIC PART NUMBER FITTING SIZE CSEE TABLE) TUBE SIZE CSEE TABLE)
Open the catalog to page 40