- Catalogs
- Layer Electronics
- Technical Data PROTON series
Technical Data PROTON series
Technical Data PROTON series
The PROTON series includes models P-401 to P-492, offering power capacities ranging from 0.6 kVA to 10 kVA. The input phase is single-phase with voltage options of 220/230/240 V ± 20%, and frequency of 50/60 Hz ± 5%. The output provides a sine wave with harmonic distortion of less than 2% and a crest factor of 2:1 for non-linear loads at 75%. Voltage output is maintained at 220/230/240 V ± 1%, with frequency stability at 50/60 Hz ± 0.2%. Overload capacities are 125% for 10 minutes, 150% for 1 minute, and 200% for 0.1 seconds. Efficiency exceeds 92% with a static switch transfer time of less than 2 ms.
The units use sealed lead-acid batteries, with options for NiCd, Li-Ion, or NaNiCl2 upon request. Energy restoration to 90% charge takes 4 hours, with stored energy times varying across models.
The system includes protections against overload, overtemperature, and voltage irregularities. Short-circuit protection is electronic, and EMI suppression is achieved with an EMI/RFI filter. Signal indicators include LED and acoustic alerts for various statuses, with an optional display.
Operating temperature ranges from 0°C to 50°C, with non-condensing humidity from 0% to 95%. Noise levels are below 60 dBA at 1 meter, and the protection rating is IP20. Dimensions and weight are available upon request.
The UPS classification is Class VFI according to EN 62040-3, with CE marking compliance to 2014/30/EU and 2014/35/EU. Standards include EN 60146-1-1, EN 62040 series, and EN 60742 for UPS, and EMC compliance to 2014/30/EU.
Factory and head office are located at S.P. km 5,3 C/da San Cusumano, 91100 Trapani, Italy. Contact via phone at +39 0923 562794 or email at [email protected].
Catalog excerpts
Technical Data PROTON series MODEL Power - kVA Input Phases Voltage Frequency Output Wave-form Harmonic distortion Crest factor (nonlinear load 75%) Voltage Frequency Overload Efficiency Static switch mains-ups Batteries Type Restored energy time Stored energy time - h Protections Short-circuit EMI Suppression Signals LED Display Acoustic Computer interface Transfer time < 2 ms Sealed lead-acid (NiCd / Li-Ion / NaNiCl2 on request) 4 hours for 90% charge level 1 Overload, overtemperature, min/max battery voltage, min/max input voltage, min/max inverter voltage, synchronism With electronic protection EMI/RFI Filter Mains, Output, Battery, Overload, Fault Optional Battery mode, low battery, overload, overtemperature, fault RS232 - RS485 - SNMP - CAN (optional) On, Stand-by, Fault Standard
Open the catalog to page 1
Environmental Temperature Non-condensing humidity Noise (at 1 m) Protection rating Dimensions W x D x H - mm Weight - kg UPS Classification according EN 62040-3 CE Marking Compliance with the standards 0°C ÷ 50°C 0% ÷ 95% < 60 dBA IP20 Request technical data Request technical data Class VFI 2014/30/EU; 2014/35/EU UPS: EN 60146-1-1, EN 62040-1-1, EN 62040-1-2, EN 62040-2, EN 62040-3, EN 60742; EMC: 2014/30/EU; Low voltage: 2014/35/EU Factory - Head Office S.P. km 5,3 C/da San Cusumano - 91100 Trapani - Italy Tel. +39 0923 562794 - Fax +39 0923 567880 Https://www.layer.it - E-mail: layer@layer.
Open the catalog to page 2All Layer Electronics catalogs and technical brochures
Technical Data CS series1 Page
Technical Data MIZAR series2 Pages
Futura7 Pages
