Kaydon Bearings Reali-Slim Bearings Catalog 300 In today's manufacturing environment, bearings are often required: Stainless Steel Reali-Slim thin section bearings mini­ ize the m surface degradation and particulate formation so com­mon in harsh environment applications. They are available: ❚❚ in AISI 440C stainless steel races ❚❚ to operate in close proximity to corrosive chemicals ❚❚ with brass or non-metallic separators ❚❚ to operate with lubricants which do not protect against corrosion ❚❚ with either stainless steel or ceramic balls ❚❚ to be ready-to-use, ultra-clean bearings with no preservative on them Kaydon stainless steel bearings are used where high precision and corrosion resistance are required. Selection Tables Stainless Steel Bearings (Material Code S) ❚❚ in either radial contact “C,” angular contact “A,” or fourpoint contact “X” configurations Because any of these requirements would disqualify the use of standard 52100 steel material, Kaydon addressed these issues by offering Reali-Slim thin section bearings in AISI 440C stainless steel. This steel meets the minimum 58 HRc hardness level and can support the same loading as does 52100 chrome steel. NOTE: In addition to the open Reali-Slim bearings on the following pages, many sealed Reali-Slim bearings are available in stainless steel. Please refer to pages 29-34 and, when ordering, replace the J in the part number with a W. All bearings made of this material also utilize balls made of AISI 440C stainless steel.

Section 2 Selection Tables Reali-Slim Bearings Catalog 300 Kaydon Bearings A deep groove bearing with reduced shoulder on one side of inner or outer race ball path. Snap-over assembly permits use of a one-piece circular pocket ring separator and greater ball complement. These bearings will accept radial load and single direction thrust load and are normally used in conjunction with another bearing of similar construction. Type A bearings require the application of thrust to establish contact angle. Stock bearings are individual units and when purchased as such must be adjusted at installation...

Kaydon Bearings Reali-Slim Bearings Catalog 300 Type A - Stainless Steel Open Reali-Slim Bearings, ANGULAR CONTACT SB Series KAYDON Bearing Number Bore Size Outside Dia. Land Diameters Radial Thrust Selection Tables Section 2 Circular pocket separator 5/32" balls .3125 L3 © F = .040 Bearing corners are normally chamfered © Capacities listed are not simultaneous. For combined loading see discussion of Bearing Selection and Load Analysis. Dynamic capacities are based upon 1 million revolutions of L10 life. Published capacities do not apply to hybrid series bearings P, X, and Y - contact Kaydon...

Reali-Slim Bearings Catalog 300 Kaydon Bearings Section 2 Selection Tables Circular pocket separator 3/16" balls © F = .040 Bearing corners are normally chamfered SD Series KAYDON Bearing Number Circular pocket separator 1/4" balls © Capacities listed are not simultaneous. For combined loading see discussion of Bearing Selection and Load Analysis. Dynamic capacities are based upon 1 million revolutions of L10 life. Published capacities do not apply to hybrid series bearings P, X, and Y - contact Kaydon product engineering for values. © Static capacities are non-brinell limits based on rigid...

Kaydon Bearings Reali-Slim Bearings Catalog 300 KAYDON Bearing Number Circular pocket separator 3/8" balls Selection Tables Section 2 ©F = .080 Bearing corners are normally chamfered KAYDON Bearing Number Circular pocket separator 1/2" balls © Capacities listed are not simultaneous. For combined loading see discussion of Bearing Selection and Load Analysis. Dynamic capacities are based upon 1 million revolutions of L10 life. Published capacities do not apply to hybrid series bearings P, X, and Y - contact Kaydon product engineering for values. © Static capacities are non-brinell limits based...

Section 2 Selection Tables Reali-Slim Bearings Catalog 300 Kaydon Bearings KAYDON Bearing Number Static© Radial Snap-over separator 1/8" balls © F = .025 Bearing corners are normally chamfered © Capacities listed are not simultaneous. For combined loading see discussion of Bearing Selection and Load Analysis. Dynamic capacities are based upon 1 million revolutions of L10 life. Published capacities do not apply to hybrid series bearings P, X, and Y - contact Kaydon product engineering for values. © Static capacities are non-brinell limits based on rigid support from the shaft and housing. ®...

Kaydon Bearings Reali-Slim Bearings Catalog 300 Type C - Stainless Steel Open Reali-Slim Bearings, RADIAL CONTACT SB Series KAYDON Bearing Number Static© Radial Snap-over separator 5/32" balls © F = .040 Bearing corners are normally chamfered © Capacities listed are not simultaneous. For combined loading see discussion of Bearing Selection and Load Analysis. Dynamic capacities are based upon 1 million revolutions of L10 life. Published capacities do not apply to hybrid series bearings P, X, and Y - contact Kaydon product engineering for values. © Static capacities are non-brinell limits based...

Reali-Slim Bearings Catalog 300 Kaydon Bearings Section 2 Selection Tables KAYDON Bearing Number Static© Radial © F = .040 Bearing corners are normally chamfered Snap-over separator 1/4" balls Bearing corners are normally chamfered © Capacities listed are not simultaneous. For combined loading see discussion of Bearing Selection and Load Analysis. Dynamic capacities are based upon 1 million revolutions of L10 life. Published capacities do not apply to hybrid series bearings P, X, and Y - contact Kaydon product engineering for values. © Static capacities are non-brinell limits based on rigid...

Kaydon Bearings Reali-Slim Bearings Catalog 300 Type C - Stainless Steel Open Reali-Slim Bearings, RADIAL CONTACT SF Series KAYDON Bearing Number Static© Radial Snap-over separator 3/8" balls © F = .080 Bearing corners are normally chamfered Selection Tables Section 2 SG Series KAYDON Bearing Number Snap-over separator 1/2" balls