Sensor Evaluation Kit, SEK002
9Pages

DESCRIPTION The Sensor Evaluation Kit, SEK002, provides an easier way to demonstrate and evaluate the following Honeywell sensors: • Basic Board Mount Pressure Sensors, ABP Series (digital versions only) • MicroPressure Board Mount Pressure Sensors, MPR Series • Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, HIH6100 Series, HIH7000 Series, HIH8000 Series, HIH9000 Series • Particle Sensors, HPM Series The kit interfaces a selected sensor to an Arduino™ Uno Rev3 Microcontroller Board. Honeywell software, which is provided free and is downloadable at http://sensing.honeywell.com/ sensors/evaluation-kit, controls the Arduino Uno Rev3 to take readings from the sensor. Sensor measurements are displayed on the user’s PC and can be recorded to a .csv file for further analysis. Sensors may be mounted directly on the SEK002 or remotely connected to the SEK002 via wire leads, allowing the sensor to be tested in adverse environments, or in a prototype product for proof of concept testing. VALUE TO CUSTOMERS • Quicker, easier sensor evaluation: The SEK002 and associated Honeywell software simplify sensor evaluation and demonstration by eliminating the need for the customer to develop any code before seeing sensor measurements. • Remote mounting: In addition to being mounted on the SEK002, the sensor may also be mounted remotely if, for example, it is to be mounted in an oven for testing or in a prototype product for proof-of-concept testing of the customer’s end product. • Cost-effective: Provides a cost-effective way learn about the capabilities of our sensors so customers can make better informed component decisions faster. Customers are then able to perform a thorough evaluation of the sensor without needing to develop additional code. • Expedites development: As the SEK002 allows customers to test their product, this helps customers to expedite their development process. FEATURES • The SEK002 has sockets and solder pads to receive the compatible sensors. The board is then plugged in as a shield board to the user-provided Arduino Uno Rev3 board. (All sensors are sold separately. Only one sensor may be evaluated at a time.) • Jumpers allow the user to select the sensor to be used, supply voltage and interface (I2C, UART or SPI). • Uses an industry standard Arduino platform. • Another Sensor Evaluation Kit (SEK001) is available for use with the TruStability™ HSC, SSC and RSC Series board mount pressure sensors. Sensor evaluation kits for other Honeywell sensors are in development. POTENTIAL APPLICATIONS • Sensor demonstration • Sensor testing and evaluation • Proof-of-concept testing

Sensor Evaluation Kit, SEK002 Table 1. Sensor Evaluation Kit Contents and User-Provided Items1 Honeywell Sensor Evalution Kit, SEK002 Includes: • Sensor Evaluation Board • Jumpers for the ABP Series ABPDLNN100MG2A5 preconfigured on the board User-Provided Components Arduino Uno Rev3 Microcontroller Board (A000066) Jumpers USB Interface Cable (Type A Male to Type B Male) Jumper Wires (for use with remote connections) Jumpers PC with Internet access (Note: If using a docking station computer, ensure that the computer is not in its docking station when installing and running the software.) The...

Sensor Evaluation Kit, SEK002 Table 2. SEK002 Compatible Sensors Basic Board Mount Pressure Sensors ABP Series—High Accuracy, Compensated/Amplified Digital output versions only DIP, SMT, leadless SMT packages: SPI, I2C output DIP MicroPressure Board Mount Pressure Sensors MPR Series—Compact High Accuracy, Compensated/Amplified Leadless SMT packages: SPI, I2C Leadless SMT mounted on breakout board Note: Refer to the product datasheet for soldering information. Honeywell HumidIcon Digital Humidity/Temperature Sensors HIH6100 Series, HIH6000 Series, HIH7000 Series, HIH8000 Series, HIH9000...

4 Sensing and Internet of Things

Figure 2. Measurement Screen for ABP Series Only Note: The example given shows the display for a pressure sensor (ABP Series, MPR series). The HumidIcon products display is similar and returns the %RH (percent relative humidity) and temperature. The HPM Series Particle Sensor returns the PM2.5 in red and the PM10 in blue, both expressing concentration in pg/m3. Honeywell I Sensor Evaluation Kit ► Pressure (ABP Series) Input Panel Captured File Clips LIVE STREAMING Table 5. Measurement Screen Functions for ABP Series Only Sensing and Internet of Things

Sensor Evaluation Kit, SEK002Front (no junipers shown) Back SENSOR EVALUATION KIT-2 *■ SEK002 g. 32328763 REV 5 6 Sensing and Internet of Things

Sensor Evaluation Kit, SEK002 Figure 5. SEK002 Dimensions (For reference only: mm/[in].) Sensing and Internet of Things

Sensor Evaluation Kit, SEK002 Figure 6. MPR Series Breakout Board Schematic and Dimensions The MPR Series sensors are available on a breakout board, allowing power and communications lines to be more easily attached to a sensor without the risk of hand soldering or the expense of creating your own evaluation PCB. The breakout board can be used with the SEK002 Sensor Evaluation Kit and software or any I2C or SPI control circuit. Breakout board dimensions (For reference only: mm/[in].) If the SEK002 is not used, please provide 1 kOhm pull up resistors on SCL and SDA lines when using I2C...

ADDITIONAL INFORMATION The following associated literature is available on the Honeywell web site at sensing.honeywell.com: • Product User Instructions A WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. For more information Honeywell Sensing and Internet of Things services its customers through a worldwide network of sales offices and distributors. For application assistance, current...