EBM Series Explosionproof Disconnect Switches
2Pages

{{requestButtons}}

Catalog excerpts

EBM Series Explosionproof Disconnect Switches - 1

EBM Disconnect Switches and Enclosures 600 VAC Heavy Duty DC using 2 AC Polyphase poles only With Switch Applications: EBM series hinged cover disconnect switches are used: • To disconnect motor, lighting and other circuits. • In locations made hazardous by the presence of flammable gases or vapors or ignitable dusts. • Indoors or outdoors in damp, wet and dirty locations, or in areas where frequent washdowns, heavy rain or water spray is prevalent. • To provide disconnect means and short circuit protection (fusible version). • On switchracks or other assemblies where it is desired that motor control be centrally located. Features: • Rugged corrosion resistant cast copper-free aluminum construction (less than 0.4 of 1%). • Switch operating handle is located through the right side wall of the body, permits visual confirmation of correct alignment and operation. • Total compliance to the wiring end room requirements of the National Electrical Code. • Semi-clamshell enclosure design, with an external flanged ground joint between body and cover makes interior components more accessible. • Minimum enclosure-to-enclosure spacing with little interference between the opened cover and an adjacent enclosure. • Stainless steel hinges allow the cover to swing well out of the way. • Stainless steel quick release captive hexhead cover bolts. Stainless steel springs provide clear indication that cover bolts are fully retracted from the body. • Switch operating handle can be padlocked in either the "ON" or "OFF" position. • Neoprene cover gasket permanently attached to the cover seals out moisture. • Bodies have top and bottom drilled and tapped conduit entrances for power and conduits. Removable reducers are supplied as standard, to accommodate smaller size conduits. All conduit entrances are plugged. • Tap on mounting feet. Certifications and Compliances: • NEC/CEC: Class I, Division 1 & 2, Groups B, C, D Class II, Division 1, Groups E, F, G Class II, Division 2, Groups F, G Class III • UL Standards: UL1203 • High A.I.C. Rating (Interrupting Capacity) - For Class I, Div. 1, Groups C & D only Volt RMS Symm-Amperes 240 65,000 • CSA Standard: C22.2 No. 30 • NEMA: 3, 3R, 4t, 4Xtt, 7BCD, 9EFG, 12 Standard Materials: • Body and cover - copper-free aluminum • Operating handle - copper-free aluminum • Operating shaft and bushing - stainless steel • Interior parts - sheet steel, electrogalvanized • Cover bolts, washers and retractile springs - stainless steel • Hinges - stainless steel Electrical Rating Ranges: • 600 VAC • 30, 60 and 100 Amp • For available options, see pages 494-495. Ordering Information: To order an enclosure complete with the disconnect switch, select the catalog number (based on the necessary rating of the switch), from the listing below. Enclosures only, without the disconnect switch, can be ordered. Select the catalog number for the required enclosure from the listing below. Without Switch Cat. # EBMBB FD W30360 EBMBB FD EBMBB FD W60360 EBMBB FD EBMBD FD W10360 EBMBD FD EBMBB FD W30361 EBMBB FD EBMBB FD W60361 EBMBB FD EBMBD FD W10361 EBMBD FD t Enclosure not suitable for NEMA 4 or 4X with cover mounted operators. ttWith S752 or S753. Copyright© 2013 Eaton’s Crouse-Hinds Business

Open the catalog to page 1
EBM Series Explosionproof Disconnect Switches - 2

Cl. I, Div. 1 & 2, Groups B, C, D Cl. II, Div. 1, Groups E, F, G Cl. II, Div. 2, Groups F, G Cl. III NEMA 3, 3R, 4‡, 4X††, 7BCD, 9EFG, 12 EBM Disconnect Switches and Enclosures Explosionproof Dust-Ignitionproof Watertight Wet Locations Dimensions are approximate, not for construction purposes. *1" D & T conduit entry for control conductors supplied with PLG plug top and bottom. **Conduit entrance(s) for power conductors (top and bottom). (All conduit entrance(s) supplied with RE reducer and PLG plug.) **J Conduit Entry Trade Size D&T† w/RE Enclosure Size Symbol ‡ Enclosure not suitable for...

Open the catalog to page 2

All EATON CROUSE-HINDS catalogs and technical brochures

  1. PRO III TCL

    2 Pages

  2. PRO APF MIRL

    2 Pages

  3. PRO III TOL

    2 Pages

  4. PRO III SBGL

    2 Pages

  5. PRO APF AGS

    16 Pages

  6. AGS-LED

    4 Pages

  7. REIL-LED

    1 Pages

  8. AV07

    2 Pages

  9. AV-LC

    1 Pages