DPI 705E
1 / 10Pages

Catalog excerpts

DPI 705E - 1

Safe area pressure indicator Hazardous area pressure indicator Druck Handheld Pressure Indicators The Druck DPI 705E Series of handheld pressure and optional temperature indicators combine tough and rugged design with accurate and reliable measurements. Compact and robust, the DPI 705E Series is designed for single handed operation and provides many essential features required for routine maintenance and system troubleshooting. Features • 41 pressure ranges from ±25 mbar to 1,400 bar (±10 inH20 to 20,000 psi/2.5 kPa to 140 MPa) • Total 1 year uncertainty down to 0.025% full scale (FS) over temperature range of -10°C to +50°C • Integral calibration record with calibration due count-down display • Rugged, handheld design with backlit high-contrast display • Leak test, tare, maximum/minimum and filter functions • Hazardous Area (Intrinsically safe) version available • Optional remote plug and play pressure (PM700E) and Resistance Temperature Detector (RTD-PROBE) sensors • Compatible with our pneumatic and hyd

Open the catalog to page 1
DPI 705E - 2

DPI 705E Improves test efficiency • 20 pressure measurement units (See below) • Impact resistant, sealed to IP54 0 to 100% FS temporary zero offset capability by subtracting the current reading from subsequent measurements. • Power on and use. No warm up time required. • 1, 3 or 5 minute leak test • Large digit high-contrast LCD with backlight • Optional carrying case with belt loop • Optional magnetic/loop hanging strap • Long battery life • Integral desk stand and hanger Zero pressure correction (gauge/differential sensors) Filter Enables a filtered pressure reading by showing a rolling...

Open the catalog to page 2
DPI 705E - 3

Pressure ranges DPI 705E Internal pressure sensors PM 700E External remote pressure sensors The DPI705E includes an internal Absolute, Gauge or Differential sensor. Any number of remote sensors can be individually used with a single DPI705E as all sensors hold their own calibration data and are supplied with a 2.9m (9.5 feet) cable. Available ranges as per table: Available ranges as per table: DPI 705E Internal pressure sensor availability PM 700E External pressure sensor availability Negative calibration option (OP1) (Gauge sensors) Full Scale Pressure Range Standard and High Accuracy...

Open the catalog to page 3
DPI 705E - 4

±0.1% FS Total accuracy over -10 to 50 degrees C including NLH&R,1 year drift and calibration uncertainty ±0.05% FS Total accuracy over -10 to 50 degrees C including NLH&R,1 year drift and calibration uncertainty ±0.025% FS Total accuracy over -10 to 50 degrees C including NLH&R,1 year drift and calibration uncertainty Accuracy specification Gauge/differential sensors Standard accuracy NLH&R High accuracy Total uncertainty Pressure range Total uncertainty Premium accuracy NLH&R Total uncertainty Absolute sensors Standard accuracy NLH&R High accuracy Total uncertainty Pressure range Total...

Open the catalog to page 4
DPI 705E - 5

Media compatibility Sensors up to and including 3.5bar (including differential) are exposed, 7-1400bar are diaphragm isolated. Working pressure 110% FS (alarm active beyond this range) Operating temperature Storage temperature MIL-PRF-28800F for Class II equipment. 1 m Drop Tested @ -20°C (-4°F) Electrical safety Media compatibility Non-condensing dry gases compatible with 316L Stainless Steel, Pyrex, Silicon, Gold, Aluminium, Glass, Silicon Dioxide and RTV Adhesive. Differential sensor reference port Non-condensing dry gases compatible with 316L and 304 Stainless Steel, Pyrex, Silicon,...

Open the catalog to page 5
DPI 705E - 6

Optional remote RTD temperature interface/probe Enabling users to perform plug and play temperature measurement capability, displaying units as resistance or temperature. The Interface only option P/N RTD-INTERFACE-485 for DPI705E Safe Area or P/N RTD-INTERFACE-IS for DPI705EIS Hazardous Area certification allows users to use their own PT100 RTD probe. RTDINTERFACE is supplied with a field-rewireable M12 connector to allow users to connect their own wire-ended RTD’s. The probe option P/N RTD-PROBE-485 for DPI705E Safe Area or P/N RTD-PROBE-IS for DPI705EIS Hazardous Area comes with the...

Open the catalog to page 6
DPI 705E - 7

Hazardous area approvals (Mandatory to select one) H0 No hazardous area approval (Default if DPI705E selected) H1 ATEX, IECEx, CSA, CCOE, XPL, KCS, NEPSI, ECASEx H2 INMETRO (Brazil) Pressure units U0 All Pressure units (Default selection) U1 Pa (Si) Pressure units only For ranges less than 350 bar (welded non-removable) For ranges less than 350 bar For ranges less than 350 bar For ranges less than 350 bar For ranges less than 350 bar Mandatory for ranges greater than/equal to 350 bar (welded non-removable) Options (Mandatory to select one) OP0 No option required OP1 Negative calibration for...

Open the catalog to page 7
DPI 705E - 8

Hazardous area approvals (Mandatory to select one) H0 No hazardous area approval (Default if DPI705E selected) H1 ATEX, IECEx, CSA, CCOE, XPL, KCS, NEPSI, ECASEx H2 INMETRO (Brazil) For ranges less than 350 bar (welded non-removable) For ranges less than 350 bar For ranges less than 350 bar For ranges less than 350 bar For ranges less than 350 bar Mandatory for ranges greater than/equal to 350 bar (welded non-removable) Options (Mandatory to select one) OP0 No option required OP1 Negative calibration for gauge ranges 20 bar and below - OP1 (Example model numbe

Open the catalog to page 8
DPI 705E - 9

Options OP1 - Negative calibration Optionally available for Gauge ranges of 20 bar and below (default for -3 accuracy). If this option is chosen, then the calibration certificate will include values down to -1 bar g. UKAS calibration We also offer UKAS accredited calibrations, please advise at the time of order placement if required. Please state any accessories required as separate items when placing order. The DPI 705E Safe and Hazardous area versions are compatible with the following accessories unless otherwise specified. Part code PM700E Remote Sensor Cable 2.9m (Cable from DPI705E to...

Open the catalog to page 9
DPI 705E - 10

Related products Process calibrators Druck offer a comprehensive range of portable pressure, temperature and electrical field calibrators. To help you select the right process calibration tools we have categorised our products into three ranges. PV212 High pressure hydraulic hand pump Lightweight, easy to use, an ideal tool for calibrating pressure transmitters, pressure transducers, pressure switches and pressure gauges. • Generates pressures up to 1000 bar (15,000 psi) Druck’s Essential range provides rugged, accurate and easy-to-use test and calibration tools. • Controlled pressure...

Open the catalog to page 10

All Druck catalogs and technical brochures

  1. PACE Tallis

    7 Pages

  2. DPI610E-Aero

    3 Pages

  3. DPS5000 I2C

    5 Pages

  4. ADTS 405 Mkll

    10 Pages

  5. ADTS542F

    6 Pages