T30S
60Pages

T30s Hand-held GCS User manual 2020.08 www.chinowing.com Shenzhen Chinowing Technology Co., Ltd

7. The Use of Parameters Setting Software of Remote Controller-19 -

Thank you for purchasing the T30S hand-held ground control station. Please use it in accordance with the local radio control regulations and read this statement carefully before using it. Once used, it shall be deemed to endorse and accept all contents of this statement. Please strictly follow this instruction to install and use the product. The supplier will not bear any legal liability for any result or loss caused by improper use, installation, final assembly or modification of the product. 1) T30s, the ground terminal (hereinafter referred to as ground unit) is used with the airborne...

7) The software, firmware, drivers, port conversion tools, etc. will be updated from time to time on our website, please visit our website to download, or contact customer service staff to obtain them. 8) If you encounter any problem during the installation or use , please contact us or visit our website at www.chinowing.com for technical support. 1) Be sure to use the spare parts provided by our company. 2) Be sure to install the antennas before power on to avoid damage to the circuit. 3) Try to make the receiver antenna without obstruction, and the end part of the antenna is vertically...

The channel number has increased from 16 to 23, and the anti-interference of data transmission and power supplies have also been optimized. Dual S-BUS can be mapped randomly in 8 analog channels, 4 three-position switches, and 11 buttons. Multi frequency can be chosen between 840MHz, 915MHz, 1.4GHz, and 2.3-2.5GHz. Stable data transmission can be provided at distances of 3-30km based on different data link versions and application environment. It can be widely used in the field of control and data transmission for industrial drones. 3.1. Item List (V20:5km grade ) T30s remote controller X1...

HDMI version

4. Product Instruction 4.1. T30S main components name ①T30S secondary display: Used for extended display of host video ②Left and right rockers: corresponding T1, T2, T3 and T4, used for flight control ③Four three-position switches: corresponding SA, SB, SD, SE www.chinowing.com

④Left and right rotary knobs: corresponding LD and RD ⑤Two buttons(or three-position switches): corresponding S1, S2 (or SC, SF) ⑥9 key channels: corresponding F1~F9 ⑦Power button and indicator: used for power on and power off the device ⑧Power, signal strength, transmitting and receiving indicator: used for indicating power, working status ⑨Left and right deflector rods: corresponding T5 and T6(return to center mode) ⑩RF antenna interfaces*2: used for connecting RF antennas ⑪Audio input and output interface: connecting headset audio output or microphone audio input ⑫LAN port ⑬USB...

③Date transmitting indicator: light will flicker in the condition of data transmitting. ④Signal strength indicator: S3 ON, signal is weak; S3 and S2 ON, signal is moderate; S3, S2 and S1 ON, signal is strong. ⑤Key switch: used for firmware upgrading, out-of-control protection settings, restore the default transmission settings. Side view ①LAN port: used for video transmission or getting video transmission parameters. ②LAN indicator: After connecting LAN port, indicator will flicker. ③TTL port: full duplex serial port ④S-Bus port: dual S-Bus output ⑤S-Bus1 data indicator: indicator will...

3. As shown in the above photo, connecting TTL port/ S-Bus port of the V20 receiver to your device by lead wire of servo. 4.With 7.4-12v DC power input, S1-S3 indicators will flicker. That means the successful connection of the transmitter and the remote control. 5. For the video input interface is LAN port, the LAN LED light will flash after the successful connection. 6. If you are using a dual S-Bus receiver, both S-Bus1 and S-Bus2 output CH1 to CH16 from the remote control. And the output of S-Bus1 and S-Bus 2 can be mapped separately. Pls refer to the output mapping description. The...

4.4. V30 Airborne Unit Indicator&Interface Instruction Front View ①Video transmission CPU indicator: light will be continuously ON in normal working condition. ②Data transmitting indicator: light will be continuously ON after successful connection of airborne unit and ground unit. ③Signal strength indicator: S3 ON, signal is weak; S3 and S2 ON, signal is moderate; S3, S2 and S1 ON, signal is strong. Side view ①Data transmission port: TTL, transparent transmission ②SBus 1 port: used for connecting flight controller or payload ③SBus 2 port: used for connecting flight controller or payload...

⑤HDMI video input interface: connecting camera ⑥USB port: used for firmware upgrading and parameters setting ⑦CVBS video input interface: used for analog video input. By default, the S-BUS1 and S-BUS2 interfaces output the CH1 to CH16 of the remote control to 1-16 channels. 4.5. V30 Receiver Installation and Connection 1. Connecting antennas to SMA port of V30. 2. Fix the receiver to the appropriate position of the aircraft by using double-sided tape. 3. As shown in the above photo, connecting TTL port/ S-Bus port of the V30 receiver to your device by lead wire of servo. TTL interface RX TX...

5. With 7.4-12v DC power input, LINK indicator will flicker. That means the successful connection of transmitter and remote control. 6. If you are using a dual S-Bus receiver, both S-Bus1 and S-Bus2 output CH1 to CH16 from the remote control. And the output of S-Bus1 and S-Bus 2 can be mapped separately. Pls refer to the output mapping description. By default, the S-BUS1 and S-BUS2 interfaces output the CH1 to CH16 of the remote control to 1-16 channels. 5. T30S Second Display Instruction 1. Before powering on the T30S, connect the HDMI and USB ports of the main display to the HDMI and...

4. In the ‘Display Options’ of the tablet PC settings, select ‘1. move the tablet display’ and ‘2. LONTIUM to do calibration. Once calibrated, it can be used normally. The factory setting of the screen display is split up and down. If the user is not used to it, right mouse click on the desktop and select "Display Settings" as shown below, No.1 is the main screen, No.2 is the secondary screen. The secondary screen can be dragged in any direction according to usage habits, and can be set in any direction of the main screen. 6. Remote Controller Operation 6.1. Power-on and Power-off of the...