Adjustable Motor, Sensor-Operated Warm Air Hand Dryer - 2 Pages

Add to MyAeroExpo favorites
Adjustable Motor, Sensor-Operated Warm Air Hand Dryer

Catalog excerpts

2922-2873, 2922-2874Adjustable Motor, Sensor-Operated Warm Air Hand Dryer SI Recommended for very high traffic areas. □ Standard Model 2922-287300 (aluminum - white) BradEX® □ Standard Model 2922-287400 (stainless steel-satin finish) BradEX® Product Materials 2922-2873 COVER: die-cast aluminum finished with white epoxy paint with Steritouch® 2922-2874 COVER: one-piece stainless steel; satin finish Cover fixed to the base plate with tamper proof screws. ADJUSTABLE MOTOR: motor is a thermally-protected universal type operating at 23,400 RPM. Adjustable motor control switch has three settings; HI, MED and LOW. HEATING ELEMENT: 400 watt heating element constructed of nichrome wire and protected by an automatic resetting thermal cutoff. Heater can be turned ON or OFF via internal switch. SENSOR OPERATION: Automatic infrared sensor with a 3 second run-on time and a 30 second vandal shut-off. BASE PLATE: Aluminum with four mounting holes and a .88" knockout. Installation Verify all rough-in dimensions prior to installation. Hand dryers require a dedicated 15 amp circuit and must be properly grounded. GFI Circuit protection is recommended. One side of dryer should be mounted to a stud. For proper mounting heights, see installation manual. Operation Place hands 3"-6" below nozzle to activate air flow. Dryer will stop after hands are removed from air flow. Surface-mounted hand dryer shall have a white cast aluminum cover with epoxy paint (2922-2873) or stainless steel cover with satin finish (2922-2874). All internal air flow paths shall incorporate SteriTouch antimicrobial technology. Hand dryer shall include aluminum base plate, adjustable universal type motor and infrared sensor. Dryer shall operate at 73 - 85 dB while delivering 78-100 CFM air at a velocity of 250 - 265 MPH or 22,000 - 23,320 LFM. Dryer shall produce air at 110 - 140°F Dryer shall have total power of 400 - 1200 watts with a consumption of 3.3 - 10.0 A. Overall dimensions: 12.5"H x 9.3"W x 7.6"D (319mm x 236mm x 192mm). Weight: Aluminum - 11.6 lb (5.2 kg) Stainless Steel - 14.2 lb (6.4 kg) Product Specifications Voltage: 100-120 V *Recess kit sold separately Orders composed of products indicated as Bradex® will be available to ship in three days after receipt of order at the factory. There is no pricing penalty for this service from Bradley. Page 1 of 2 5/29/2014 This information is subject to change without notice. Bradley_HandDryer_2922-2873_2874

 Open the catalog to page 1

2922-2873, 2922-2874 Adjustable Motor, Sensor-Operated Warm Air Hand Dryer Dimensions Surface Mounted 0.88" (22mm) knockout for bottom entry surface-mounted conduit 3.2" (82mm) from side of rough opening Front View Wall Box Mounting 8.5" (216mm) from bottom of rough opening Wiring Entry 5.2" (132mm) from top of rough opening Rear View Wall Box Mounting *Recess kit sold separately Orders composed of products indicated as Bradex® will be available to ship in three days after receipt of order at the factory. There is no pricing penalty for this service from Bradley. Page 2 of 2 5/29/2014 This...

 Open the catalog to page 2

All Bradley Corporation catalogs and technical brochures

  1. CLE SERIES

    8 Pages

  2. HL Series

    8 Pages