- Catalogs
- ARESIA - ST SOUPPLETS
- USB charge tester for Aircraft maintenance
USB charge tester for Aircraft maintenance
USB charge tester for Aircraft maintenance
- Dimensions: 85mm x 50mm x 36mm (including USB connector)
- Weight: >90g
- Power Input: 4.0VDC-25.0VDC
- Configurable Drawn Current: 0.05A to 3.50A ± 2%
- Working Temperature: -10°C to +25°C
- Storage Temperature: -10°C to +60°C
- The 2235E device is designed to consume a configurable USB port power supply.
- Features include RoHS/REACH compliance, CE compliance, heat dissipation with a fan, and overheat and overvoltage protection.
- Includes a USB type A port, white polyamide casing, printed circuit, fan, two buttons, and a potentiometer for setting current using a digital display.
- Plug the device into the USB port to be tested. The digital display will blink in current display mode by default.
- Set the drawn current value using the potentiometer (clockwise).
- Press the ON/OFF button to activate the charge; the display will stabilize and show the measured current. The fan may activate depending on ambient temperature.
- Press the ON/OFF button again to deactivate the charge; the display will blink and show the drawn current target.
- Check the device for any cracks or broken pieces before powering on.
- Ensure the USB connector is correctly attached.
- Do not obstruct air circulation through the device.
- Do not use air blown guns to clean the device; use a clean, slightly wet cloth instead.
- Overvoltage Protection (OVP): Activates when voltage exceeds 25V; components may be permanently damaged above 30V.
- Overheat Protection (OTP): Activates when component temperature exceeds 80°C.
- Overpower Protection (OPP): Activates when power exceeds 25W.
- To reset, unplug the device.
- A switched-off display indicates the device is not powered.
- A blinking display indicates no active charge.
- A still display indicates an active charge.
- The 'P' and 'V' modes are for measurement only; activating the configured charge returns the display to current mode.
Catalog excerpts
6 rue du 5 septembre 1914, 77165 SAINT SOUPPLETS, France +33 1 60 01 53 72 Web : www.seca-auto.com : [email protected] The 2235E device allows to consume a configurable USB port power supply. Current configurable RoHS / REACH Сє compliant Drawn current : 0.05 A → 3.50 A Heat dissipation with fan Overheat and overvoltage protection Display of measured values Dimensions L x l x h: Weight : Power input : Configurable drawn current : Working temperature: Storage temperature : Digital display The 2235E010 includes USB type A port, a white polyamide casing, printed circuit, fan, two buttons, a potentiometer to set the current using the digital display. ON/OFF button SET button
Open the catalog to page 1
6 rue du 5 septembre 1914, 77165 SAINT SOUPPLETS, France +33 1 60 01 53 72 Web : www.seca-auto.com : [email protected] Quickstart ⚠ The potentiometer position corresponds to a drawn current target; any modification of this position (on or off) will modify this target. Plug the device on the USB port to be tested, directly or using the adaptation cable. The digital display will blink on the current display mode by default. Set the drawn current value using the potentiometer (clockwise). Push the « ON/OFF » button to activate the charge, the display turns still and display the measured current....
Open the catalog to page 2All ARESIA - ST SOUPPLETS catalogs and technical brochures
Mixed Reality service1 Page
SECA Equipment6 Pages
- Aeronautical software
- Real-time software
- Maintenance software
- 3D software
- Tester
- Aeronautical tester
- Test bench
- Aeronautical test bench
- Aircraft lighting
- Test software
- Aircraft cabin lighting
- Avionics tester
- Aeronautical test instrument
- Test instrument
- Portable tester
- AC/DC power supply
- Avionics test instrument
- Aircraft power supply
- Portable test instrument