DVHV2800S
1 / 17ページ

DVHV2800S SeriesHIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION The DVHV series of high-reliability DC-DC converters provide decades of successful critical mission support. Operable over the full military (-55 °C to +125 °C) temperature range with no power derating, the DVHV series unique input, and output filters dramatically reduce input and output noise performance. While operating at a nominal fixed frequency of 450 kHz, these regulated, isolated units utilize a high-speed magnetic feedback design and well-controlled under-voltage lockout circuitry to eliminate slow start-up problems. These converters are designed and manufactured in a facility qualified to ISO9001 and certified to MIL-PRF-38534 and MIL-STD-883. This product may incorporate one or more of the following U.S. patents: 5,784,266 5,790,389 5,963,438 5,999,433 6,005,780 6,084,792 6,118,673 FEATURES • High Reliability • Very Low Output Noise • Output Voltage Trim Up +10% or Down -20% • Wide Input Voltage Range: 15 to 50 Volts per MIL-STD-704 • Up to 15 Watts Output Power • Fault Tolerant Magnetic Feedback Circuit • NO Use of Optoisolators • Undervoltage Lockout • Indefinite Short Circuit Protection • Current Limit Protection • Industry Standard Pinout • High Input Transient Voltage: 80 Volts for 1 sec per MIL-STD-704A • Precision Seam Seal Hermetic Package • Custom Versions Available • Additional Environmental Screening Available • Meets MIL-STD-461 Revisions C, D, E and F EMC Requirements When Used With VPT’s EMI Filters • Flanged and Non-flanged Versions Available. • MIL-PRF-38534 Element Evaluated Components • Space Applications should consider VPT’s "S” Series of Radiation Tolerant Power Conversion Devices. Contact VPT for details. Sales Information: Phone: (425) 353-3010 Fax: (425) 353-4030 E-mail: vptsales@vptpower.com

DVHV2800S SeriesSPECIFICATIONS (Tcase = -55°C to +125°C, Vin = +28V ± 5%, Full Load, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by qualification testing. 5. Correction factor of 0.12 added to ceramic capacitors.

DVHV2800S SeriesSPECIFICATIONS (Tcase = -55°C to +125°C, Vin = +28V ± 5%, Full Load, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. Correction factor of 0.12 added to ceramic capacitors.

DVHV2800S SeriesSPECIFICATIONS (Tcase = -55°C to +125°C, Vin = +28V ± 5%, Full Load, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS Notes: 1. Dependent on output voltage. 2. Time for output voltage to settle within 1% of its nominal value. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. Correction factor of 0.12 added to ceramic capacitors.

DVHV2800S Series BLOCK DIAGRAM PIN 1 UNDER VOLTAGE SHUTDOWN PRIMARY HOUSEKEEPING SUPPLY VOLTAGE AND CURRENT AMPLIFIERS SECONDARY HOUSEKEEPING SUPPLY

DVHV2800S Series INHIBIT DRIVE CONNECTION DIAGRAMS Figure 4 – Internal Inhibit Circuit and Recommended Drive Figure 5 – Isolated Inhibit Drive (Shown with optional capacitor for turn-on delay) (Shown with optional capacitor for turn-on delay) EMI FILTER HOOKUP DIAGRAM Figure 6 – Converter with EMI Filter

DVHV2800S Series PARALLEL CONNECTION DIAGRAM

DVHV2800S SeriesOUTPUT VOLTAGE TRIM The output voltage can be trimmed down by connecting a resistor between the TRIM pin (PIN 3) and the +V OUT pin (PIN 5), or can be trimmed up by connecting a resistor between the TRIM pin (PIN 3) and the OUT COM pin (PIN 4). The maximum trim range is +10% up and -20% down. The appropriate resistor values versus the output voltage are given in the trim table below.

DVHV2800S Series EFFICIENCY PERFORMANCE CURVES (Tcase = 25°C, Full Load, Unless Otherwise Specified)

DVHV2800S Series EMI PERFORMANCE CURVES (TCASE = 25°C, VIN = +28V ± 5%, Full Load, Unless Otherwise Specified) Figure 13 – DVHV2800S without EMI Filter Figure 14 – DVHV2800S with EMI Filter

DVHV2800S SeriesPACKAGE SPECIFICATIONS (NON-FLANGED, SEAM SEAL) 0.405' max [10,29mn] SIDE VIEW NDTESi 1, DIMENSIONAL LIMITS ARE +0.005' UNLESS OTHERWISE STATED, 2, CASE TEMPERATURE IS MEASURED ON THE CENTER OF THE BASEPLATE. 3, MATERIALS: CASFi STEEL, GOLD OVER NICKEL PLATED. COVER; KOVAR, NICKEL PLATED. PINS: COPPER CORED ALLOY 52, GOLD OVER NICKEL PLATED, PIN SEALS: CERAMIC Figure 15 - Non-Flanged, Seam Seal Package and Pinout

DVHV2800S SeriesPACKAGE SPECIFICATIONS (FLANGED, SEAM SEAL) PIN Figure 16 - Flanged, Seam Seal Package and Pinout

DVHV2800S SeriesENVIRONMENTAL SCREENING (100% Tested Per MIL-STD-883 as referenced to MIL-PRF-38534) Test 1. Contact Sales for more information concerning additional environmental screening and testing options desired. 2. VPT Inc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our sole discretion unless specifically forbidden by customer contract. 3. 100% R&R testing with all test data included in product shipment. 4. Not required per MIL-PRF-38534. Test is performed for additional product quality assurance. 5. Non-QML products may not meet all...

DVHV2800S SeriesORDERING INFORMATION DVHV 1. Contact the VPT Inc. Sales Department for availability of Class H (/H) and KL1 (/KL1) qualified products. 2. VPT Inc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our sole discretion unless specifically forbidden by customer contract. 3. -KL1 products are identical in every way with Class K products in compliance with MIL-PRF-38534 revision L and later revisions except they contain elements evaluated to the requirements of MIL-PRF-38534 revision K and previous revisions. These devices are not marked...