Tool Catalog
1 / 88Pagine

HELICOPTER CORPORATION Illustrated Tool Piston & Turbine

Lead Lag Nut Wrench Damper Rod End Removal Tool Main Rotor Blade Bolt guide Bullet Main Rotor Hoist Sling TR Gearbox Rigging Tool, A Model Lamiflex Nut Socket Needle Point Grease Adapter Swashplate Tie-bolt Wrench Transmission Hoist Eye Tail Rotor Blade Nut, A Model Collective Capsule Retainer Tool Main Rotor Blade Tab Bending Tool Main Rotor Blade Tab Angle Tool Idler Pulley Installation Kit Oleo Holding Tool Main Rotor Grip Seal Instalation Tool Pulley Alignment Tool Lower Swashplate Dogleg Puller Main Rotor Mast Nut Tool Main Rotor Flapping Nut Tool Tail Rotor Balance Bracket Pinion Nut...

Tail Rotor Driveshaft Alignment Tool Grip Seal Installation Tool Flapping Bearing Inst Tool, (Grease Lube) Tail Rotor Balance Bracket Fan Balance Bracket Oil Fill Tube Wrench Damper Piston / Seal Tool U-Block Seal Installation Tool Flapping Bearing Inst Tool, Oil Lube Upper Pulley Restraining Tool Oil Cooler Shaft Alignment Tool Tail Rotor Blade Assy Holder Oleo Disassembly Tool Seal Tool, Inst. Engine Stand Bearing Press Kit Fuel Nozzle Removal Tool Torque Multiplier Tool Rotor Hub Stand Turbine Fuel Probe Socket Hub Puller Swashplate Centering Tool Blade Weight Removal Tool Upper...

Lead Lag Nut Wrench PISTON & TURBINE Special wrench for hub lead lag nut. Used to remove and install lead lag retention nut Hub is pictured here up-side-down.

Damper Rod End Removal Tool PISTON & TURBINE Special Wrench for Lead Lag Damper Shaft Use to remove the rod end from the damper

T-0009 Blade Bolt Bullet PISTON & TURBINE Alignment tool for Main Rotor Blade Pin Installed on main rotor blade bolt to aid in alignment while installing bolt

T-0011 Rotor Hub Sling Piston & Turbine Tool for slinging the helicopter or hub / transmission assembly Used to sling the helicopter for working on the landing gear, and also to remove and install the hub / transmission assembly in the helicopter The entire weight of the helicopter can be lifted off the ground using this method.

T-0012 Tail Rotor Rigging Tool PISTON Tail Rotor Control Rigging Tool Tool used to set tail rotor control rigging in A and 280 models Neutral pedal position. Full right pedal position Full left pedal position

T-0013 Lamiflex Nut Socket PISTON & TURBINE (ONLY SOME EARLY 480s) Lamiflex Retention Nut Socket Used to remove and Install Lamiflex retention nut on piston aircraft and on a few early 480 models

T-0014 Needle Point Grease Adapter PISTON & TURBINE Special tool for greasing TR Teeter Bearings Installs on grease gun for lubing the TR Spindle Teeter Bearings

T-0016 Swashplate Tie-bolt Wrench PISTON & TURBINE Special Wrench for Swashplate Tie Bolt Used to hold the swashplate tie bolt for assembly and disassembly Used to hold swashplate tie-bolt while assembling lower swashplate assembly.

T-0017 Transmission Hoist Eye TURBINE & PISTON Main Rotor Transmission Shaft Support Tool Used to sling main transmission when the hub is not installed

T-0020 A Model Tail Rotor Blade Retention Nut PISTON (A MODEL) TR Blade Bearing Retention Nut Wrench Used to remove and install the TR grip bearing retention nuts on A model 3.3 “ chord blade only

T-0022 Collective Capsule Restraining Tool PISTON & TURBINE Collective Spring Capsule Restraining Tool Used to restrain the collective capsule spring pressure when removing and installing the spring capsule in the helicopter

T-0026 Blade Tab Bending Tool PISTON & TURBINE Trim Tab Adjusting Tool Used to adjust main rotor blade trim tabs when tracking blades

T-0027 Blade Tab Angle Tool PISTON & TURBINE Blade Trim Tab Protractor Used to read trim tab angles

T-0029 Idler Pulley Installation Kit PISTON Idler Pulley Bearing Installation Tools Used to support and align the idler pulley bearings while removing and installing bearings.

T-0035 Oleo Holding Tool PISTON & TURBINE Special Wrench for Landing Gear Oleos Used to hold the Seal Housing Assembly while disassembling the landing gear oleos

T-0036 Main Rotor Grip Seal Installation Tool PISTON & TURBINE Special Tool to Install Grip Seal Used to push the seal into the grip when installing the grip on the spindle.

T-0044 Pulley Alignment Tool PISTON Lower Pulley Alignment Tool Used to check and adjust alignment of upper and lower pulley in piston aircraft.

T-0045-1 Dog Leg Puller PISTON & TURBINE Puller for Main Rotor Push-Pull Control Rods Used to remove dog leg assemblies from control rods

T-0048 Main Rotor Mast Nut Tool PISTON & TURBINE Special Wrench for Mast Nut Used to remove and install the upper mast nut

T-0051-3 Flapping Nut Tool PISTON & TURBINE Special Wrench for Flapping Pin Nut Used to remove and install flapping pin nut

T-0052 Tail Rotor Balance Bracket PISTON & TURBINE Optical Sensor Attach Bracket Used to hold the optical sensor while dynamic balancing the tail rotor assembly

T-0053 Pinion Nut Wrench (Obsolete) PISTON Main Rotor Transmission Pinion Nut Wrench Old style wrench used to remove and install pinion nuts. Replaced by T-0135-1-SET

T-0054 Dog Leg Alignment Tool PISTON & TURBINE Dog Leg Alignment Tool Used to align dog legs during installation onto main rotor push-pull control rods

T-0056-3 Tail Rotor Grip Bearing Retention Nut Wrench PISTON & TURBINE Special Wrench for TR bearing retention nut Used for removal and installation of TR Grip bearings on spindle. Also used to torque tail rotor gearbox input shaft nut.

T-0057 Damper Cycling Tool PISTON & TURBINE Special Tool to Cycle Main Rotor Lead-Lag Dampers Used to cycle dampers to bleed air following maintenance.

T-0068-3 TR Gearbox Indicator Tool TURBINE & PISTON Tool for Measuring Runout on Tail Rotor Gearbox Output Shaft Used to measure runout on TRGB shaft with dial gauge

T-0078 Engine Adapter Installation Tool PISTON Engine Oil Filler Tube Adapter Special Wrench Used to install the oil filler tube adapter into the crankcase of the Lycoming engine

T-0079 Dog Leg Bearing Swaging Tools PISTON & TURBINE Press Tool for Installing ECD030-11 Bearings Used to install dog leg uniball bearings.