DataMan® 260 Series
1 / 34Pagine

DataMan® 260 Series Quick Reference Guide

Precautions To reduce the risk of injury or equipment damage, observe the following precautions when you install the Cognex product: l This device requires the use of an LPS or NEC class 2 power supply (nonPoE device) or the use of a PoE Class 1 (PoE device). Do not connect or disconnect this device from the I/O module or 15-pin USB adapter cable when the I/O module or adapter cable is connected to a PC. Route cables and wires away from high-current wiring or high-voltage power sources to reduce the risk of damage or malfunction from the following causes: over-voltage, line noise,...

This product does not contain user-serviceable parts. Do not make electrical or mechanical modifications to product components. Unauthorized modifications can void your warranty.

Symbols The following symbols indicate safety precautions and supplemental information: WARNING: This symbol indicates a hazard that could cause death, serious personal injury or electrical shock. CAUTION: This symbol indicates a hazard that could result in property damage. Note: This symbol indicates additional information about a subject. Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.

Product Overview Illumination LEDs Trigger button Power indicator Train status indicator Good/bad read indicator Network status indicator Error indicator Tune button

Ethernet connector Note: *Use only one set of mounting holes (either 3 OR 4) for mounting. Note: The five status LEDs together also function as a peak meter using an orange light. DataMan 260 Accessories LENS OPTIONS, COVERS, ILLUMINATIONS AND FILTERS Accessory Name Accessory Number IR 6.2 mm lens kit, 3 -position with IR LED IR 16 mm lens kit 16 mm lens with extended optics mount (requires the use of an extended front cover and high-powered red LED) UV Light Kit for 6.2 mm lens (365nm) Liquid Lens Module (LLM) to be used with 6.2 mm lens or 16 mm lens Accessory Image

ImageMax kit Clear lens cover* Clear lens cover, ESD safe* Polarized front cover* Extended lens cover, un-polarized** Extended lens cover, half-polarized ** Extended lens cover, fully polarized** Blue bandpass filter Red bandpass filter Red LED illumination* White LED illumination* Blue LED illumination* High Powered red LED illumination** Note: *Use with a 6.2 mm lens only! **Use with a 16 mm lens only! ***ESD safe

Accessory Name Accessory Number CCBL-05-01 CCB-M12x12Fy-xx (y=S: straight / y=A: angled *, xx specifies length) CCB-M12xDB9Y-05 Connection cable RS-232 Adapter cable, M12x12 to M8x4/M8x5, 0.5 m X-Coded to RJ45 Ethernet Cable Adapter cable, ETH, M12, X-CODED/A-CODED, 0.5 m CCB-84901-2001-xx, where xx can be 02, 05, 10, 15 or 30, indicating length in meters CCB-M12x8MS-XCAC DM100-UBRK-000 Universal Mounting Bracket Pivot Mounting Bracket Accessory Image

Dimensional Drawings The size of the DataMan 260 in the angled configuration is shown in the following figures:

The size of the DataMan 260 with the extended lens cover configuration is shown in the following figures:

The size of the DataMan 260 with the side read mirror configuration is shown in the following figure:

Field of View and Reading Distances Horizontal Field of View values Device DM260 Short Range: 77 mm [3.0 Long Range: 115 mm [4.5 Short Range: 34 mm [1.3 Short Range: 50 mm [1.9 in] Short Range: 87 mm [3.4 Long Range: 123 mm [4.8

Vertical Field of View values Device

Short Range: 28 mm [1.1 Short Range: 42 mm Long Range: 92 mm [3.6 Long Range: 108 mm [4.25 in] Long Range: 135 mm [5.3 Long Range: 223 mm

Reading Distance for 1D and 2D Codes with 6.2 mm Lens Distances in mm/ 2D min. code 6.2 mm lens Long Range Distances in mm/ 1D min. code 6.2 mm lens Long Range

Distances in mm/ 2D min. code 6.2 mm lens Short Range Distances in mm/ 1D min. code 6.2 mm lens Short Range

Reading Distance for 1D and 2D Codes with 16 mm Lens Distances in mm/

DataMan 260 Readers with Side Read Mirror The following table shows the Field of View (FoV) widths of DM260 with 6.2 mm lens focused to 190 mm at various distances.

The following table shows the Field of View (FoV) widths of DM262 with 6.2 mm lens focused to 190 mm at various distances. Device DM262

Connecting the Reader Perform the following steps: 1. Mount the reader. 2. Connect the Ethernet cable (CCB-84901-2001-05) either to a computer or a switch. 3. Connect the breakout cable (CCBL-05-01). For information on the pinout and wire colors, see section Connections, Optics and Lighting in the DataMan 260 Reference Manual.

Installation Installation procedures and specifications are presented in detail in the DataMan® 260 Reference Manual, which is installed with the DataMan Setup Tool. From the Windows Start menu, select the following to access the manual: All Programs > Cognex > DataMan Software vx.x.x > Documentation. Note: l l Cables are sold separately. If a standard component is missing or damaged, immediately contact your Cognex Authorized Service Provider (ASP) or Cognex Technical Support. CAUTION: All cable connectors are keyed to fit the connectors on the reader. Do not force the connections or...

Connect the Ethernet Cable 1. Connect the Ethernet cable's M12 connector to the reader ENET connector. 2. Connect the Ethernet cable’s RJ-45 connector to a switch/router or PC, as applicable. Connect the Breakout Cable Note: You can clip unused wires short or use a tie made of non-conductive material to tie them back. 1. Verify that the 24VDC power supply is unplugged and not receiving power. 2. Attach the Breakout cable's +24VDC and GROUND to the corresponding terminals on the power supply. CAUTION: Never connect voltages other than 24VDC. Always observe the polarity shown. 3. Attach the...

Install Software and Documentation and Connect the Reader Follow the steps below to connect your reader to power and network: 1. Connect the I/O+RS232+24V cable to your reader. 2. For a network connection, connect your reader through an Ethernet cable to your network. 3. Connect the cable to a 24V power supply. To configure a DataMan 260 reader, the DataMan Setup Tool software must be installed on a networked PC. The DataMan Setup Tool is available from the DataMan support site: http://www.cognex.com/support/dataman. 1. After installing the software, connect the DataMan 260 Series reader to...