DVPL0510S
1 / 13Seiten

DVPL0510S SeriesHIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION The DVPL series of high reliability DC-DC converters is operable over the full military (-55 °C to +125 °C) temperature range with no power derating. Operating at a nominal fixed frequency of 300 kHz, these regulated, non-isolated converters are optimized for low voltage point of load applications with high efficiency synchronous rectification, fast transient response, and power sequencing capability. These converters are designed and manufactured in a facility qualified to ISO9001 and certified to MIL-PRF-38534 and MIL-STD-883. This product may incorporate one or more of the following U.S. patents: 5,784,266 5,790,389 5,963,438 5,999,433 6,005,780 6,084,792 6,118,673 FEATURES • High Reliability • Operates From 5V Input • Adjustable Output Voltage, 0.8V to 3.4V • Up to 10 Amps or 33W Output • High Efficiency, Up to 96% • High Power Density: >100 W/in3 • Output Voltage Sequencing • Output Voltage Tracking • Operation Into a Pre-Biased Output • Output Inhibit Control • Low Output Noise • NO Use of Optoisolators • Over Current and Short Circuit Protection • Precision Projection Welded Hermetic Package • Meets MIL-STD-461C and MIL-STD-461D EMC Requirements When Used With VPT DC-DC Converters and EMI filters • Additional Environmental Screening Available • MIL-PRF-38534 Element Evaluated Sales Information: Phone: (425) 353-3010 Fax: (425) 353-4030 E-mail: vptsales@vptpower.com

1. Dependent on output voltage. 2. Time for output voltage to settle within 1% or 20mV of its nominal value, whichever is greater. 3. Derate linearly to 0 at 135°C. 4. Verified by initial electrical design verification. Post design verification, parameter shall be guaranteed to the limits specified. 5. With 100pF capacitor from Vin to Ground. 6. Vout not necessarily in regulation. 7. Correction factor of 0.12 added to ceramic capacitors.

DVPL0510S Series BLOCK DIAGRAM B PIN 1 5 VIN UNDER VOLTAGE SHUTDOWN PIN 5 PRIMARY HOUSEKEEPING SUPPLY FEEDBACK COMPENSATION NETWORK INH VOLTAGE TRACK CIRCUITRY Figure 3 (Shown with recommended 100uF input capacitor)

DVPL0510S Series TYPICAL DISTRIBUTED APPLICATION DVFL2805S DC/DC CONVERTER 1 TRACKING APPLICATION

INTERNAL CONNECTION DIAGRAMS Figure 6 – Internal Inhibit Circuit and Recommended Drive Size (Shown with optional capacitor for turn-on delay) Figure 7 – Internal Track Circuit 14-Aug-2006 Sheet of W:\unReleased VPT Drawings\..\DVPL0510S_Diagram s-A.Sch Drawn By : +VOUT Number 14-Aug-2006 Sheet of W:\unReleased VPT Drawings\..\DVPL0510S_Diagrams-A.Sch Drawn By : Figure 8 – Track timing relations

OUTPUT VOLTAGE TRIM The output voltage is set with an external resistor connected from the TRIM pin to the GND pin 7. This resistor must have a tolerance of 1% or less to achieve an accurate output voltage. The default output voltage with the TRIM pin left open is 0.80V. Figure 9 - Output Voltage Trim

DVPL0510S Series EFFICIENCY PERFORMANCE CURVES (TCASE = 25°C, Full Load, Unless Otherwise Specified) VOUT = 3.3V Efficiency (%) vs Output Current (A) 98 96 Efficiency (%) Figure 10 – DVPL0510S Vin=5.0V Efficiency (%) vs. Output Current (A)

DVPL0510S Series EMI PERFORMANCE CURVES (Tcase = 25°C, Full Load, Unless Otherwise Specified) MIL-STD-461C CED3 Narrowband Emission Level [dB>iA] Emission Level [dBuA] Emission Level [dBuAl Emission Level [dBpA] Emission Level [dBuA] Figure 13- 28V input line, DVME, DVFL and DVPL, Cin=100pF 8

NOTES! 1. DIMENSIONAL LIMITS ARE ±0.005" UNLESS OTHERWISE STATED, 2, CASE TEMPERATURE IS MEASURED ON THE CENTER OF THE BASEPLATE, 3, MATERIALS: CASE; STEEL, GOLD OVER NICKEL PLATED, COVER! STEEL, NICKEL PLATED, PINS; COPPER CORED ALLOY 52 (O,O4O"0), ALLOY 52 (O.O25"0), GOLD OVER NICKEL PLATED. PIN SEALS! GLASS Figure 14 - Package and Pinout

DVPL0510S Series ENVIRONMENTAL SCREENING (100% Tested Per MIL-STD-883 as referenced to MIL-PRF-38534) Test © Contact Sales for more information concerning additional environmental screening and testing options desired. © VPT I nc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our sole discretion unless specifically forbidden by customer contract. @ 100% R&R testing with all test data included in product shipment. © Not required per MIL-PRF-38534. Test is performed for additional product quality assurance. © Non-QML products may not meet all...

ORDERING INFORMATION Notes: 1. Contact the VPT Inc. Sales Department for availability of Class H (/H) or Class K (/K) qualified products. 2. VPT Inc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our sole discretion unless specifically forbidden by customer contract. Please contact your sales representative or the VPT Inc. Sales Department for more information concerning additional environmental screening and testing, different input voltage, output voltage, power requirement, source inspection, and/or special element evaluation for space or...

SMD (STANDARD MICROCIRCUIT DRAWING) NUMBERS Do not use the DVPL0510S Series similar part number for SMD product acquisition. It is listed for reference only. For exact specifications for the SMD product, refer to the SMD drawing. SMDs can be downloaded from the DLA Land and Maritime (Previously known as DSCC) website at https://landandmaritimeapps.dla.mil/programs/defaultapps.asp. The SMD number listed above represents the Federal Stock Class, Device Type, Device Class Designator, Case Outline, Lead Finish and RHA Designator (where applicable). Please reference the SMD for other screening...