• Products
  • Catalogues
  • News & Trends
  • Exhibitions

Fluorosint PTFE - 8 Pages

Add to MyAeroExpo favorites
Fluorosint PTFE
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

Catalogue excerpts

Fluorosint® PTFE Family of Advanced Fluoropolymer Materials

 Open the catalogue to page 1

Fluorosint® enhanced ptfe materials SEE HOW THESE MATERIALS STACK UP IN YOUR APPLICATION Quadrant developed the FLUOROSINT® range of enhanced PTFE materials to fill the performance gaps where unfilled and low-tech, filled PTFE based polymers underperform. Each FLUOROSINT material was specifically developed to excel in demanding bearing and seal applications. While each of these materials possess the chemical resistance and compliance of PTFE, each material offers some special benefits that give the designer clear performance advantages. Higher pressure seals and wear parts where precision is critical. Fluorosint...

 Open the catalogue to page 2

Fluorosint® 500 EXCEPTIONAL DIMENSIONAL STABILITY FOR PRECISE TOLERANCE CONTROL Common applications FLUOROSINT® 500 Enhanced PTFE offers an ideal combination of stability and wear resistance for sealing applications where tight dimensional control is required. FLUOROSINT 500 also greatly reduces the risk of a catastrophic system failure by becoming a sacrificial wear surface. With a deformation under load 9 times lower than virgin PTFE, FLUOROSINT 500 allows designers to greatly improve the efficiency of systems without sacrificing the wear resistance and forgiving benefits of PTFE. The synthetic...

 Open the catalogue to page 3

Fluorosint® 207 LOWEST COEFFICIENT OF FRICTION OF FLUOROSINT GRADES Common applications FLUOROSINT® 207 Enhanced PTFE is a significant performance upgrade for any designer using PTFE for applications where temperature resistance, chemical resistance and food contact compliance (FDA and 2002/72/EC) are all important. FLUOROSINT 207 lasts far longer than unfilled PTFE in wear applications and has a very low coefficient of friction. FLUOROSINT 207 works well against most mating surfaces. · Seals · Mixers · Pumps · Appliances · Bearings · Valve seats Application example FLUOROSINT 207 replaces unfilled...

 Open the catalogue to page 4

Fluorosint® HPV MOST WEAR RESISTANT FLUOROSINT GRADE – OUTLASTS LOW-TECH PTFE BASED MATERIALS Common applications FDA compliant FLUOROSINT® HPV is a high performance bearing grade of FLUOROSINT – optimized for high PV and very low wear factor. FLUOROSINT HPV was developed for bearing applications where other, low-tech PTFE formulations exhibit premature wear or simply cannot perform. FDA compliance gives food and pharmaceutical equipment manufacturers new design options and all benefit from its excellent load bearing and wear characteristics. · Bearings · Commercial food equipment · Wear guides...

 Open the catalogue to page 5

Fluorosint® MT-01 ULTRA-HIGH PERFORMANCE GRADE FOR STABILITY AT ELEVATED TEMPERATURE Dark grey Common applications FLUOROSINT® MT-01 is an extreme service grade developed specifically for applications where the benefits of PTFE-based materials also require strength, stiffness and stability. FLUOROSINT MT-01 delivers high mechanical performance at elevated temperature and as a result is often specified in seat, seal and wear applications where extreme conditions are present. · High temperature seals · Linear guides · Wear bands · Ovens and dryers Application example FLUOROSINT MT-01 is widely specified...

 Open the catalogue to page 6

PHYSiCAL PROPERTiES OF THE FLUOROSINT® GRADES Properties Note: 1 g/cm3 = 1,000 kg/m3 ; 1 MPa = 1 N/mm2 ; 1 kV/mm = 1 MV/m.    - : currently no data available (1) According to method 1 of ISO 62 and done on discs 0 50 x 3 mm. (2) Only for short time exposure (a few hours) in applications where no or only a very low load is applied to the material. (3) Temperature resistance over a period of min. 20,000 hours. After this period of time, there is a decrease in tensile strength - measured at 23 °C - of about 50 % as compared with the original value. The temperature values given here are thus based...

 Open the catalogue to page 7

Quadrant Engineering Plastic Products worldwide: North America Quadrant EPP Asia Pacific Ltd 60 Ha Mei San Tsuen, Ping Shan Yuen Long – N.T. Hong Kong Tel +852 (0) 24702683 Fax +852 (0) 24789966 E-mail: asia.epp@qplas.com BELGIUM | CHINA | FRANCE | GERMANY | HONG KONG | HUNGARY | INDIA | ITALY | JAPAN | KOREA | MEXICO | POLAND SOUTH AFRICA | SWITZERLAND | THE NETHERLANDS | UNITED KINGDOM | UNITED STATES OF AMERICA This brochure and any data and specifications presented on our website shall provide promotional and general information about the Engineering Plastic Products (the «Products») manufactured...

 Open the catalogue to page 8

All QUADRANT EPP catalogues and technical brochures

  1. Ertalyte®

    6 Pages

    En
  2. Duratron® PBI

    1 Pages

    En